We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

Spot Hogg Fast Eddie Bow Sight: Setup, Pin Tuning and Tips

Learn how to set up a spot hogg fast eddie bow sight, tune pins and sight in for accurate shots. A clear beginner guide with steps and common mistakes to avoid.

Updated November 2026

A spot hogg fast eddie bow sight is a single-pin, slider-style sight that many target archers mount on a riser to keep their aim consistent from one shot to the next. In this guide you will learn how to mount the sight, set the pin height and tune the pin to your draw length, so you can sight in at a safe, known distance and start shooting groups you can trust.

Before You Mount the Sight

Start with the bow itself. The sight needs a stable, correctly tuned bow to work properly, so confirm that your arrow is spined correctly, your nocking point is set and your cams or limbs are synced. A sight cannot correct a bow that is shooting erratically.

Shopping for one? See our guide: Bow Sights with Rangefinder: 5 Best Picks Compared (2026).

Check the mounting hardware and the sight’s fit to your bow’s sight bracket. Loosen the bracket screws only enough to slide the sight in place. Tighten nothing yet.

Mounting and Setting the Sight Position

Position the sight so the pin sits roughly in line with your arrow when you come to full draw. Most archers find it easiest to set the slider close to the middle of its travel range first, then adjust from there. Keep the sight housing level with the ground so the pin’s vertical and horizontal adjustments work as intended.

  1. Attach the sight to the bracket loosely and slide it to the center of its travel range.
  2. Draw the bow to your normal anchor and check that the pin sits on the target area with your head in a natural position.
  3. Tighten the bracket screws evenly, then recheck your anchor point. Shift your head, not the sight, if your cheek weld feels off.
  4. Confirm the sight is level using a bubble level or a plumb line hung from the riser.

Sighting In at a Known Distance

Begin at a short, known distance, such as 10 or 15 yards, on a target face you can see clearly. Shoot three to five arrows from a rested position, and focus on a consistent anchor and release. Once your groups are tight, use the windage and elevation adjustments to move the group onto the center of the target.

Next, move back to your target distance in measured steps. At each distance, record the pin setting that puts your arrows in the center. Many archers mark these settings on tape near the pin housing. Manufacturer instructions for the specific model will describe exact adjustment screws and travel limits, so check those before you turn anything beyond its stop.

Fine-Tuning Pin Position

If your arrows group high or low, adjust the vertical setting in small increments, usually a quarter turn at a time. Shoot a full group after each change before adjusting again. Avoid chasing a single bad arrow; look at the overall group center instead.

Common Mistakes and Tips

  • Changing the bow setup and the sight at the same time, which makes it impossible to tell which change caused a shift in impact.
  • Sighting in with an inconsistent anchor point or release, so the sight is being tuned to the shooter’s errors rather than the bow.
  • Over-tightening bracket screws, which can strip threads or shift the sight after tuning.
  • Skipping a level check. A tilted sight will throw off elevation at longer distances.
  • Shooting too far before the sight is set. Start short and work outward.

A sturdy bow square or level helps you confirm the sight sits square before you start tuning. View on Amazon

A bubble-style sight level clips onto the riser and makes it easy to check sight alignment on every session. View on Amazon

A small adjustment tool set with the right hex and Allen bits helps you make precise changes without stripping screws. View on Amazon

FAQ

Do I need to level the spot hogg fast eddie bow sight before I sight in?

Yes. A level sight keeps your vertical and horizontal pin movements true, so your groups will track correctly at longer distances.

How far should I shoot when first setting up this sight?

Start at a short, known distance such as 10 to 15 yards. Move outward only after your groups are tight and centered.

What should I do if my arrows keep grouping low after tuning?

Check your anchor point and release for consistency first. If the group is still low, make small vertical adjustments and shoot a full group after each change. Consult a qualified archery pro shop if the problem persists, since it may point to a bow tuning issue.

Conclusion

With the sight mounted level, sighted in at a short distance and adjusted in small steps, your spot hogg fast eddie bow sight should give you repeatable aim. Record your pin settings at each distance so you can return to them quickly. Revisit the setup whenever you change arrows, draw length or bow tuning.

Ethan Brooks

About Ethan Brooks

Ethan Brooks is part of our editorial team and reviews and edits our target archery guides, checking product details against manufacturer specifications and owner feedback.

About the author

Ethan Brooks
Ethan Brooks

Ethan Brooks writes reviews and buying guides for Archery Society.