We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

Pvc Bow Arrow Rest: What It Is and How to Make or Set One Up

Learn what a pvc bow arrow rest is, when it makes sense, and how to build and tune a simple one for stable arrow flight. Beginner-friendly steps inside.

Updated November 2026

A pvc bow arrow rest is a simple, low-cost shelf made from PVC pipe that holds your arrow on the bow’s riser while you draw and release. This guide explains what a pvc rest does well, where it falls short, and how to cut, mount and tune one so your arrows fly straight enough for practice and beginner shooting.

What a PVC Arrow Rest Does

An arrow rest gives the arrow a stable platform so it does not sit on the bow hand or slide off during the shot. A PVC rest is typically a short piece of pipe or fitting shaped into a shelf, sometimes padded with felt or foam, that is attached to the riser with tape, a bracket or a threaded insert. Because PVC is rigid, inexpensive and easy to shape, it is a common choice for homemade setups on traditional and recurve bows.

Shopping for one? See our guide: Arrow Rest for Compound Bow: 6 Best Picks Compared (2026).

The main limitation is that PVC does not compress or flex the way a dedicated rest material does. Arrows can bounce or ride unevenly if the shelf is too high, too hard or badly aligned, so the fit matters more than the material itself.

Materials and Tools You Need

  • Schedule 40 PVC pipe or a short fitting, about 1/2 inch in diameter
  • Hacksaw or PVC cutter
  • Fine sandpaper or a deburring tool
  • Felt, moleskin or thin foam for the contact surface
  • Strong double-sided tape or a rest mounting bracket
  • Measuring tape, a bow square and a fletched arrow for testing

Step-by-Step: Building and Mounting the Rest

  1. Cut the shelf. Cut a section of PVC roughly 1.5 to 2 inches long. Cut it lengthwise or file one side flat so it sits flush against the riser.
  2. Smooth the edges. Sand all cut edges so they cannot scrape the arrow shaft or fletching.
  3. Pad the contact point. Glue or tape felt or foam to the top surface where the arrow rests. Keep the padding thin so it does not raise the arrow too far.
  4. Position on the riser. Mount the rest on the riser about 1/8 inch above the arrow centerline for most setups, then check that the arrow sits level with the string.
  5. Test the fit. Nock a fletched arrow and make a few slow draws. The arrow should sit on the shelf without tilting or sliding.

Tuning for Clean Arrow Flight

A rest that looks right can still cause poor groups. Shoot a few arrows at a close target, about 5 to 10 yards, and watch how each one leaves the bow. Paper tuning, where you shoot through paper stretched on a frame, shows whether the arrow is tilting in flight. If the arrow tail drifts to one side, adjust the rest height or sideways position in small steps of about 1/16 inch.

Symptom Likely cause Adjustment
Arrow fishtails left or right Rest too far to one side Move rest toward the tail-drift direction
Arrows fly high or low Rest height off Raise or lower in 1/16 inch steps
Arrow bounces off shelf Shelf too hard or edge rough Add padding, re-sand edges

Common Mistakes

  • Leaving sharp or burred edges that tear fletching
  • Making the shelf too tall, which lets the arrow tilt on release
  • Skipping the level check against the string
  • Mounting the rest without confirming the bow’s arrow pass-through clearance
  • Assuming a homemade rest tunes itself; always test with paper or a close target
  • Felt or moleskin sheets give a soft, quiet contact surface that is easy to replace when worn. View on Amazon
  • Paper tuning frame kit lets you check arrow flight at close range before you commit to a height. View on Amazon

If you want a rest that adjusts without DIY work, compare a few options in Arrow Rest for Archery: 7 Best Picks Compared for Recurve and Compound Bows. For recurve-specific mounting, see Recurve Bow Arrow Rest Placement: A Step-by-Step Guide for Beginners and How to Install Arrow Rest on Recurve Bow: A Step-by-Step Guide for Beginners. Compound shooters may find Compound Bow Arrow Rest Adjustment: A Step-by-Step Guide for Beginners useful, and Traditional Bow Arrow Rest: 7 Best Picks Compared for 2026 covers traditional setups.

FAQ

Is a PVC arrow rest safe to use?

Yes, for light practice shooting, provided the edges are smooth and the rest is firmly mounted. Check it before each session, and replace it if it cracks or loosens.

Can a PVC rest replace a commercial one for hunting?

Most hunters prefer a dedicated rest with consistent, tested performance. A homemade rest can work, but it is harder to verify under field conditions. Consult an experienced archery instructor before relying on any homemade gear for hunting.

How high should the PVC shelf sit?

Start with the shelf about 1/8 inch above the arrow centerline, then adjust in small steps based on paper tuning results.

Conclusion

A pvc bow arrow rest can give beginners a stable, inexpensive starting point when it is cut cleanly, padded and mounted level. Tune it with paper or close-range shooting rather than guessing. Once you understand how your arrows fly, you can decide whether a commercial rest is worth the upgrade.

Ethan Brooks

About Ethan Brooks

Ethan Brooks is part of our editorial team and reviews and edits our target archery guides, checking product details against manufacturer specifications and owner feedback.

About the author

Ethan Brooks
Ethan Brooks

Ethan Brooks writes reviews and buying guides for Archery Society.