Compound Bow Arrow Rest Adjustment: A Step-by-Step Guide for Beginners
Learn compound bow arrow rest adjustment step by step: centershot, height, timing and tuning tips so your arrows fly straight and your groups tighten up.
Updated November 2026
Compound bow arrow rest adjustment comes down to four things: centering the rest side to side, setting its height so the arrow sits level, timing the rest so it drops away cleanly, and fine-tuning the setup so arrows fly straight from the bow. Work through the steps below in order and you will end up with a rest that holds the arrow steady at full draw and releases it without interference.
Most new archers blame their form for erratic groups when the real culprit is a rest that is a few millimeters off. This guide walks through the adjustments in the order they should be made, explains what each one does, and lists the mistakes that cause the most trouble. Before you start, it helps to know what type of rest you have. If you are still choosing one, the overview in Compound Bow Arrow Rest Types: 5 Best Picks Compared (2026) explains the differences between drop-away, whisker biscuit and capture styles.
Shopping for one? See our guide: Arrow Rest for Compound Bow: 6 Best Picks Compared (2026).
Before You Start: Tools and Preparation
Adjusting a rest is not difficult, but it goes much faster when you have the right tools on hand and a stable setup to work from. Gather the following before you begin.
- A bow press or a bow stand that holds the bow steady and level
- Hex (Allen) keys in the sizes your rest and bracket use, typically 3/32 inch and 5/64 inch
- A small flat-blade screwdriver or a rest-specific tool for fine adjustments
- A centershot gauge or a plumb line and a tape measure
- Two or three test arrows of the same length and spine, cut to your draw length
- A paper tuning target or a bag target, placed at 5 to 10 yards
- A dry-erase marker or painter’s tape to mark settings as you go
Start with a bow that is properly tuned at the cam level and string. If the bow is cocked or the cams are timed unevenly, rest adjustments will chase a problem they cannot fix. Check that the string is not twisted, that the nocking point is set, and that the bow’s draw length matches your current form. Manufacturers generally specify that a bow should be tuned before any rest work begins, and that advice holds.
Step 1: Set the Centershot Position
Centershot describes how far the arrow sits from the bow’s center line. Most compound bows are designed to shoot best with the arrow centered over the riser, but the exact target varies by model and by arrow. Getting this right first gives every later adjustment a solid starting point.
How to Measure Centershot
- Set the bow upright in the press or stand, with the string at rest.
- Measure from the front of the riser’s center line (the vertical line running through the grip) to the back of the string at the nock point. Record this figure.
- Measure the same distance at the arrow’s rest contact point. The difference shows how far the arrow sits off center.
- Adjust the rest’s side-to-side position until the arrow sits at the target centershot figure your bow manufacturer lists. Many guides suggest a starting point of roughly 0.25 to 0.5 inch for most compounds, but always verify against your bow’s own spec.
Move the rest in small increments, about 1/16 inch at a time, and recheck after each change. If your rest has a side-to-side slot, loosen the mounting screws slightly, shift the rest, then retighten. Avoid cranking it all the way over in one motion, because you will lose track of where you started.
Step 2: Set the Rest Height
Height determines whether the arrow sits level with the string when the bow is at rest and at full draw. An arrow that sits too high or too low will porpoise or fishtail, and it can make your groups jump high or low even when your aim is consistent.
Checking Arrow Level
- Nock an arrow and set it on the rest with the bow at rest.
- Sight down the arrow from the rear. The shaft should look parallel to the string, with the nock and the string sitting on a level plane.
- If the arrow tilts up at the back, lower the rest. If it tilts down, raise the rest.
- Raise or lower the rest in increments of 1/32 to 1/16 inch and recheck.
Height adjustments on most rests use a vertical slot or a threaded post. Loosen the lock nut, make the change, then tighten it while holding the rest in place so it does not shift. Many archers find it easiest to set height with the arrow nocked and the bow in a stand, then confirm again with the bow drawn.
Step 3: Adjust Rest Timing and Drop-Away Function
If you use a drop-away rest, timing determines when the arm falls away from the arrow during the shot. The arm should be fully clear of the arrow before the arrow leaves the bow. Too early and the arrow loses support before it is stable; too late and the arrow can be struck or deflected by the rest arm.
- Drop-away arms are usually timed with a cable, a cam-driven trigger or a spring-loaded arm. Check the manufacturer’s manual for the timing point.
- Many rests are set so the arm begins to drop as the string passes the rest’s contact point and is fully clear before the nock reaches the rest.
- Observe the rest in slow motion by drawing and releasing the string with the arrow removed, or by using a camera to record the shot.
Timing adjustments are typically made with the cable length or the arm tension, not the rest’s position. Change them in small steps and retest, because a timing change can alter arrow flight in ways that look like a centershot problem. For a closer look at how these components interact, see Drop Away Arrow Rest for Compound Bow: 7 Best Picks Compared (2026).
Step 4: Fine-Tune with Paper or Bare Shaft Testing
Once centershot, height and timing are set, check arrow flight with a paper tear test or a bare shaft test. These are the most reliable ways to confirm that the rest is not causing the arrow to fly off-axis.
Paper Tuning
- Set up a paper target at about 3 to 5 feet from the bow, with a frame or stand that holds the paper taut.
- Shoot one arrow through the paper from close range.
- Study the tear. A clean hole with feathers or fletching that tear neatly indicates good flight. A tear that shows a tail to one side means the arrow is hitting the rest or the bow hand is pulling it off-axis.
- Adjust the rest’s side position or height in small amounts, then shoot again.
Bare Shaft Testing
Shoot a bare arrow (no fletching) at 10 to 15 yards. If the bare shaft flies straight with the fletched arrows, the rest is not the source of a problem. If the bare shaft hits to the left or right of the fletched groups, the arrow is pulling off the rest or the centershot is off. Shoot the bare shaft and a fletched arrow alternately to compare them directly.
Step 5: Check Torque and Lock Everything Down
Rests loosen over time because of string vibration and repeated shooting. Check every mounting screw and adjustment lock after your initial setup and again after every few sessions. Use hex keys that fit snugly, and tighten to the snugness your rest manual recommends rather than forcing screws to the limit. Overtightening can strip threads or crack plastic brackets.
Common Mistakes to Avoid
- Adjusting too many things at once. Change one variable, test, then change the next. Otherwise you cannot tell which adjustment solved the problem.
- Ignoring the bow’s cam timing. A bow that is out of tune will look like a rest problem. Fix the bow first.
- Using arrows that are the wrong spine. Even a perfectly set rest will struggle with arrows that are too stiff or too weak for the bow’s draw weight and length.
- Forgetting to lock adjustments. A rest that drifts during a session will give inconsistent groups that look like a form issue.
- Setting height with the bow at rest only. Check arrow level at full draw too, because some rests shift slightly under load.
- Skipping the paper test. Visual adjustments are a good start, but paper and bare shaft testing reveal problems you cannot see by eye.
Tips for Consistent Results
- Keep a written log of every setting: centershot measurement, height, timing and arrow model. This makes it easy to return to a known-good setup.
- Recheck your rest after changing arrows, string material or draw length.
- Shoot from a stable stance and consistent anchor point so you can judge whether a change helped or whether your own form changed.
- If a problem persists after careful adjustment, ask an experienced archery shop or a certified technician to look at the bow. A second set of eyes often spots issues you have stopped seeing.
If you are comparing rests before you adjust one, the broader guide to Arrow Rest Set Up: 5 Best Picks Compared for Recurve and Compound Bows covers the setup process from a buyer’s standpoint. For hunting setups, where reliable arrow flight matters even more, 6 Best Compound Bow Arrow Rests for Hunting: Picks Compared (2026) is a useful companion read. Archers with other bow styles may also find Top 7 Archery Bow Arrow Rest Options Compared for Recurve and Compound Bows helpful when comparing features.
Recommended gear
- Bow press: A stable press holds the bow level and frees both hands for adjustments, which makes centershot and height work much faster and more accurate. View on Amazon
- Hex key set: A set that includes the sizes your rest and bracket use prevents stripped screws and makes small adjustments easier to hold. View on Amazon
- Paper tuning frame: A frame that holds paper taut lets you run a clean paper test at close range and see arrow flight clearly. View on Amazon
- Centershot gauge: A gauge or plumb line set gives repeatable centershot measurements so you can return to a known setting. View on Amazon
FAQ
How often should I adjust my compound bow arrow rest?
Check your rest after every major equipment change, and inspect it every few sessions for loose screws or drift. A full re-tune is usually only needed when arrows, string or draw length change.
What is the most important compound bow arrow rest adjustment?
Centershot is usually the first priority, because it sets the baseline for arrow flight. Height and timing come next, and fine-tuning with paper testing finishes the job.
Can I adjust the rest without a bow press?
Yes, but a bow press or stand makes the work faster and more precise. Without one, have a helper hold the bow steady and be extra careful about measurements.
Why does my arrow fishtail after I adjust the rest?
Fishtailing usually points to rest height or to an arrow that is not spined correctly for your bow. Check arrow level first, then verify that your arrows match your draw weight and length.
How do I know if my drop-away rest is timed correctly?
The arm should be fully clear of the arrow before the nock reaches the rest’s contact point. Slow-motion video is the most reliable way to confirm this.
Do I need to re-tune the rest after changing arrows?
Often yes. Different shaft diameters, lengths and weights can change how the arrow sits on the rest and how it flies, so recheck centershot, height and paper tuning.
When should I take my bow to a professional?
If you cannot achieve clean paper tears after careful adjustment, or if you notice cracked brackets, stripped threads or damaged cables, have a qualified archery technician inspect the setup. Safety-related damage to a bow should be assessed by a professional before shooting.
Conclusion
Compound bow arrow rest adjustment is a sequence, not a guessing game. Set centershot first, then height, then timing, and finish with paper and bare shaft tests to confirm clean flight. Log your settings as you go so you can return to a setup that works, and always check the bow itself before blaming the rest.
Ready to choose one?
