Aae Champion Ii Arrow Rest: Setup, Tuning and Tips for Target Archers
Learn how to set up and tune an aae champion ii arrow rest for target archery, with step-by-step setup, common mistakes and tips for beginners.
Updated November 2026
The aae champion ii arrow rest is a drop-away style rest that holds your arrow in place until the moment of release, then gets out of the way. This guide walks you through the parts you need to check, how to mount and adjust the rest, and how to tell whether your arrow is flying cleanly. Work through the steps in order and you should end up with a rest that is square, secure and ready for tuning.
What to Check Before You Mount the Rest
Before you touch the bow, confirm that your riser has the right threaded holes and that your rest’s mounting hardware matches them. Most target bows use a standard hole pattern, but check your bow’s manual or measure the hole spacing with a ruler.
Shopping for one? See our guide: AAE Free Flyte Micro Arrow Rest: 6 Best Picks Compared (2026).
- A hex key set in the sizes your rest and bow require
- A square or a small bubble level
- A fletched arrow of your normal setup, cut to your draw length
- A clean target face and a stable target at a known distance, usually 10 to 20 yards
- A bow square or a long straightedge for checking alignment
How to Mount the Aae Champion Ii Arrow Rest
Mount the rest loosely first so you can adjust its position before tightening everything down. Set the rest on the riser at the height that centers the arrow on the bow’s shooting line, then fasten the mounting screws finger-tight.
- Attach the rest bracket to the riser using the supplied screws, leaving them loose.
- Set the arrow on the rest and check that the nock sits at your normal nocking point.
- Check vertical alignment with your square or level so the rest sits square to the string.
- Tighten the screws evenly, a little at a time, to avoid bending the bracket.
- Confirm the rest moves freely in its drop-away motion and returns without binding.
Tuning the Rest for Clean Arrow Flight
Once the rest is mounted, tuning comes down to two checks: how the arrow sits on the rest when you draw, and how it flies on paper. A common starting point is to shoot a single arrow at a paper target from a short distance and look at the hole it leaves. Adjust the rest in small increments, about one turn of an adjustment screw at a time, and shoot again after each change.
Reading the Paper Test
A tear in the paper that points left or right usually means the arrow is nocking or leaving the rest at an angle. Make small horizontal adjustments first, then re-check. Vertical tears often point to nocking point or rest height, so adjust those separately.
Common Mistakes and Tips
- Tightening the mounting screws fully before alignment is checked, which makes later adjustment difficult.
- Changing several settings at once, which makes it impossible to tell which change helped.
- Skipping a re-check of the nocking point after the rest is moved.
- Ignoring a rest that binds on the drop-away return, which can disturb arrow flight.
- Assuming a new rest is tuned out of the box; every bow and arrow combination needs checking.
For background on how the rest fits with the rest of your setup, see Types of Arrow Rest: A Guide to Each Style for Archers and What Holds Arrows in Archery: Quivers, Arrow Rests and Holders Explained. If you are comparing other drop-away designs, Schaffer Archery Opposition Arrow Rest: Setup Steps and Tuning Tips covers a similar installation approach.
Recommended Gear
- Bow square: helps you confirm the rest sits square to the string before you shoot. View on Amazon
- Hex key set: gives you the right sizes for mounting and adjusting the rest without stripping screws. View on Amazon
- Paper tuning target: makes the paper test quick to run and easy to read. View on Amazon
FAQ
Do I need special tools to install an aae champion ii arrow rest?
You will need a hex key set that matches the rest’s hardware and a square or level for alignment. A bow square makes the alignment check more reliable.
How often should I re-check the rest’s setup?
Check it after any change to your bow, string, arrow length or nocking point, and periodically if you shoot often. Small shifts in screws can change arrow flight over time.
Can a rest setup fix a problem I have with grouping?
A rest can cause grouping problems if it is out of alignment, but form and release also affect grouping. If the paper test looks clean and your groups are still wide, check your shooting form with a coach. Consult a qualified archery instructor for personal form advice.
Conclusion
A properly mounted aae champion ii arrow rest sits square, moves freely and gives your arrow a clean path to the target. Take your time with alignment and change one setting at a time during tuning. Once the paper test shows a clean hole, shoot a full group to confirm the setup holds up.
Related reading
Ready to choose one?
