We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

Recurve Bow Arrow Rest Placement: A Step-by-Step Guide for Beginners

Learn recurve bow arrow rest placement step by step: find your centershot, set height and tune for clean arrow flight. A beginner-friendly guide from Archery So

Updated November 2026

Recurve bow arrow rest placement comes down to three measurements: the horizontal position of the rest (centershot), its height above the shelf, and its angle relative to the arrow. Get those right and your arrow leaves the bow with minimal contact, flies straight, and groups tighter on the target. This guide walks through each setting in the order most beginners find easiest.

Before You Start: Gather the Right Tools

You do not need a shop full of equipment, but a few basics make the job far more accurate.

Shopping for one? See our guide: 6 Best Bow and Arrow Rests for Recurve and Traditional Bows (2026).

  • A bow square or a straightedge to check the arrow line
  • A tape measure with millimeter markings
  • A bow stringer and a sturdy target with a backstop
  • Your arrows, cut to the correct length for your draw
  • Paper and tape for a paper tune, if you plan to check arrow flight

Confirm your bow is strung correctly and the string is not twisted before adjusting anything. A crooked string throws off every measurement that follows.

Setting the Horizontal Position (Centershot)

Centershot is the horizontal distance between the center of the bow’s riser and the arrow shelf. Most recurve bows perform best with the arrow centered on the string, or very close to it. Start by measuring from the string center to the riser center at the grip, then measure from the string to the inside edge of the shelf.

Many recurve archers begin with the rest positioned so the arrow sits just left of center for right-handed shooters, then fine-tune from there. Move the rest in small increments, about 1 mm at a time, and shoot a few arrows after each change. Shooting a paper tune at each step shows you whether the arrow is flying cleanly.

Adjusting Rest Height

Rest height determines where the arrow sits relative to the bow’s center line. Place the arrow on the rest and sight down it with your bow square. The arrow should sit level with the string at nocking point height. If the rest is too high, the arrow will ride above the intended line; too low, and it will drop into the riser.

Quick height check

  1. Nock an arrow at your normal nocking point.
  2. Rest the arrow on the shelf and bring it to full draw, then release slowly.
  3. Watch the arrow’s tail in the bow sight line. If it dips, raise the rest slightly. If it rises, lower it.

Setting the Angle and Final Tuning

The rest should hold the arrow so it sits parallel to the bow’s centerline at rest. Many recurve bows use a rest angle that lets the arrow lift slightly off the shelf at release. Check this with a paper tune: shoot an arrow through a sheet of paper taped to a frame, then examine the tear pattern.

Paper tear result What it suggests Adjustment
Clean hole with the fletching visible Good arrow flight Make only minor changes
Tear in the upper right area Arrow is coming off the shelf too early Move rest slightly toward the riser
Tear in the lower left area Arrow is being pushed too far out Move rest slightly away from the riser

Make changes one at a time and reshoot the paper after each adjustment. Changing several settings at once makes it impossible to know which one helped.

Common Mistakes to Avoid

  • Adjusting the rest on a bow with a loose limb bolt or cracked string
  • Changing height and centershot in the same session without checking each separately
  • Ignoring arrow spine, since a mismatched shaft can look like a rest problem
  • Placing the rest by eye instead of measuring from the string center
  • Tightening rest screws so hard the rest shifts under vibration

A bow square helps you check arrow alignment accurately. View on Amazon

A paper tuning frame lets you check arrow flight at close range without guessing. View on Amazon

FAQ

How far should a recurve arrow rest be from the riser?

There is no single distance that suits every bow. Start by measuring to centershot from the string center, then adjust in small steps while checking arrow flight on paper.

Can I place a recurve arrow rest without a bow square?

You can estimate placement with a tape measure and a straightedge, but a bow square gives far more repeatable results. Consistency matters more than perfection at the start.

Do I need to re-tune after changing my arrows?

Yes. Different arrow spine, length or point weight changes arrow flight, so recheck the rest position and paper tune after any change to your setup.

Conclusion

Recurve bow arrow rest placement is a repeatable process: set centershot, check height, then fine-tune with a paper tune. Work slowly and change one setting at a time. With a little patience, your arrows will leave the bow cleanly and group more reliably.

Ethan Brooks

About Ethan Brooks

Ethan Brooks is part of our editorial team and reviews and edits our target archery guides, checking product details against manufacturer specifications and owner feedback.

About the author

Ethan Brooks
Ethan Brooks

Ethan Brooks writes reviews and buying guides for Archery Society.