We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

How to Adjust a Trophy Ridge Bow Sight: Step-by-Step for Beginners

Learn how to adjust a Trophy Ridge bow sight step by step, from leveling and setting pin gaps to sighting in at 20 yards for accurate shots.

Updated November 2026

To adjust a Trophy Ridge bow sight, you level the sight, set the pin gaps for your draw length, and then sight in each pin at a set distance. The whole process takes most archers under an hour at the range. Once you finish, your pins will line up with where your arrows actually land.

What You Need Before You Start

Gather your tools before you touch the sight. Most adjustments take only a few minutes once you have everything within reach.

Shopping for one? See our guide: Bow Sights with Rangefinder: 5 Best Picks Compared (2026).

  • A hex (Allen) key set, usually 3/32-inch and 5/64-inch, matching your sight’s mounting and adjustment hardware
  • A bubble level, either the one built into your sight or a separate clip-on level
  • A target at a known distance, starting with 20 yards
  • A marking tool or blue painter’s tape to flag your arrow groups
  • A bow square or arrow to check the sight’s vertical alignment

Step 1: Level the Sight

A sight that tilts sideways will throw your shots off to one side, no matter how well you aim. Start by checking the bubble level while the bow is held upright and at full draw alignment.

  1. Loosen the mounting screws just enough to let the sight move.
  2. Rotate the sight until the bubble sits centered between the lines.
  3. Tighten the mounting screws without shifting the sight.
  4. Recheck the level after tightening, since the sight can drift slightly.

Step 2: Set Pin Gaps and Adjust Pins

Pin gaps are the vertical spacing between your pins, and they set how each pin aims at a different distance. Many Trophy Ridge sights come with a rough starting setup, but you still need to tune them to your bow.

Start with the 20-yard pin. Move the sight housing up or down along the slide until the top pin sits just above the arrow’s path at that range. Your pins will reflect your draw length and arrow speed, so expect to fine-tune them over several sessions. Bow Mounted Fish Finder: How to Choose and Install One (2026) goes further into this.

Adjusting Windage

Windage moves the pins left and right. Use the windage adjustment screw to shift the sight until your arrows group in the center of the target horizontally. Make small turns, about a quarter turn at a time, and shoot a group before making another change.

Step 3: Sight In at Your First Distance

Stand at 20 yards and shoot three to five arrows at the 20-yard pin. Look at where the group lands, not at any single arrow.

Arrow group location Adjustment
High on the target Lower the pin or move the sight down slightly
Low on the target Raise the pin or move the sight up slightly
Left of center Adjust windage to move the pin right
Right of center Adjust windage to move the pin left

After each adjustment, shoot another group before changing anything else. Repeat until the group is centered on your aim point, then move to the next distance.

Common Mistakes to Avoid

  • Adjusting the sight without leveling it first, which forces you to compensate with your form.
  • Making large turns on the adjustment screws, which overshoots the correction.
  • Judging your group from one or two arrows instead of a full set.
  • Tightening the mounting screws too hard, which can strip threads or shift the sight.
  • Changing your draw length or anchor point and then wondering why your sight is off.

A bow square makes it much easier to confirm that your sight and arrow rest are aligned before you start adjusting. View on Amazon

A clip-on bubble level lets you check leveling quickly at the range without fumbling with your sight’s built-in level. View on Amazon

If your sight is not behaving as expected, you may also want to read Trophy Ridge React V5 Bow Sight: Setup, Pin Tuning and Tips for Beginners for a deeper look at pin tuning, or Trophy Ridge Drive Slider Bow Sight: What It Is and How to Use It if your sight uses a slider system.

FAQ

How often should I adjust my Trophy Ridge sight?

Check your sight whenever you change arrows, draw length, or string, and after any bow shipping or transport. A quick group check at 20 yards is usually enough to confirm nothing has shifted.

Why does my sight keep moving after I tighten it?

Loose mounting hardware or overtightening can both cause movement. Use firm, even pressure on the screws and recheck the level after tightening. If the problem continues, consult a bow technician.

Can I sight in my bow indoors?

Yes, as long as you have a safe backstop and enough distance for your chosen range. Lighting matters, so check the official product manual or ask a shop professional for guidance on indoor setup.

Conclusion

Adjusting a Trophy Ridge bow sight comes down to three steps: level it, set your pin gaps, and sight in at a known distance. Work through each step in order and make small adjustments between groups. With patience, your pins will match your arrow flight.

Ethan Brooks

About Ethan Brooks

Ethan Brooks is part of our editorial team and reviews and edits our target archery guides, checking product details against manufacturer specifications and owner feedback.

About the author

Ethan Brooks
Ethan Brooks

Ethan Brooks writes reviews and buying guides for Archery Society.