Dual Trac Bow Sight: A Step-by-Step Setup Guide for Beginners
Learn how a dual trac bow sight works, how to mount it, and how to sight in both tracks for accurate shots at close and long range. Beginner-friendly steps.
Updated November 2026
A dual trac bow sight uses two sight tracks so you can adjust pin positions for near and far shots without changing your setup. This guide walks you through what the design does, how to mount it, and how to sight in both tracks so your pins land where you expect. Work through the steps in order and you will end up with a sight that is stable, level and tuned to your bow.
What a Dual Trac Bow Sight Does
A standard single-track sight moves its pins along one vertical path. A dual trac design adds a second track, usually set at a slightly different angle or on a separate slider, so you can dial in two distinct pin groups. Many archers use one track for close distances and the other for longer shots, which keeps you from relying on a single pin across a wide range of yardages.
Shopping for one? See our guide: Bow Sights with Rangefinder: 5 Best Picks Compared (2026).
Before you touch any screws, confirm that your bow’s draw length, brace height and arrow setup are already correct. A sight can only be as accurate as the bow it sits on.
Mounting and Leveling the Sight
Mount the sight to the riser using the bracket and mounting holes that came with your bow or sight. Tighten the bolts snugly but not so hard that you strip the threads or warp the bracket. Then check level:
- Hang a plumb line or use a bubble level on the sight housing with the bow held vertically at full draw.
- Adjust the sight’s left-right and rotation until the reference line is perfectly vertical.
- Recheck after tightening, because the bracket can shift slightly under torque.
Confirm that the sight does not contact the arrow or the rest at full draw. Clearance matters more than most beginners expect.
Sighting In Both Tracks
Sight in one track completely before you touch the second. Set your target at a known distance, such as 20 yards, and shoot a group of at least three arrows with the first track active. Adjust the pin until your group centers on the bull, then lock the setting.
Setting the Second Track
Move to your second distance, often 40 or 50 yards, and switch to the second track. Shoot a group, note where it lands relative to your aim point, and adjust the pin in small increments. Recheck the first track at its own distance after every change, because the two tracks can influence each other.
Work in small steps. Quarter-turn adjustments on most sights correspond to modest movements on the target, and overcorrecting wastes time and arrows.
Checklist Before You Shoot
- Bow draw length and brace height confirmed
- Sight mounted and level at full draw
- Pin housing secure, with no loose screws
- First track sighted at its distance
- Second track sighted at its distance
- Shooting groups logged for future reference
Common Mistakes
- Adjusting both tracks at once, which makes it hard to tell which change caused which result.
- Skipping the level check, leaving pins tilted and shots drifting left or right.
- Shooting from unsteady positions. Use a consistent stance and anchor point.
- Overtightening the mounting bolts, which can strip threads or distort the bracket.
- Ignoring arrow fletching or rest contact that changes arrow flight.
Recommended Gear
- Bubble level for bow sights: A small level clipped to the sight or riser makes leveling faster and more repeatable. View on Amazon
- Hex key set for archery: Sight adjustments and mounting bolts often use hex fasteners, so a compact set keeps your tuning kit ready. View on Amazon
- Target stand with paper faces: A consistent target at known distances makes sighting in much easier. View on Amazon
For more on specific sight models and setup, see Trophy Ridge Drive Slider Bow Sight: What It Is and How to Use It and Mounting a Bow Sight: A Step-by-Step Guide for Beginners. If you are weighing single-pin and multi-pin designs, Single Pin or Multi Pin Bow Sight (2026): Which Is Better for Beginners? covers the tradeoffs.
FAQ
Do I need to sight in both tracks every time I shoot?
You only need to sight in both tracks once, then recheck them periodically. Bumps, temperature changes or a new string can shift your settings, so a quick group at each distance is good practice.
Can a dual trac sight replace a multi-pin sight?
It depends on your shooting. Two tracks cover two distance ranges well, while a multi-pin sight gives you more fixed reference points across more yardages.
What if my groups keep drifting after adjustment?
Check that the sight is tight, level and not touching the arrow or rest. If problems persist, a local archery pro shop can inspect your setup in person.
Conclusion
A dual trac bow sight gives you two sight-pin groups for different distances, which can make shooting more consistent once it is set up correctly. Mount it level, sight in one track at a time, and log your groups as you go. Patient, methodical adjustment will do more for your accuracy than any single setting.
Related reading
- Xero A1i Pro Bow Sight: Setup, Pin Tuning and Tips for New Archers
- What Is the CBE Tactic Hybrid 1-Pin Bow Sight and Is It Right for You?
- What Is a Sight Master Bow Sight and How Do You Set One Up?
Ready to choose one?
