We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

Mounting a Bow Sight: A Step-by-Step Guide for Beginners

Learn how mounting a bow sight works, from picking the right bracket to setting height, level and torque so your pins line up at every distance.

Updated November 2026

Mounting a bow sight correctly means attaching the sight bracket to your bow, setting it level and square to the arrow path, and locking it down so the pins stay aligned after a few hundred shots. Done right, the sight will hold its zero, and you will be able to aim the same way every time you draw. This guide walks through the process for most compound and recurve setups.

What You Need Before You Start

Gather everything before you touch the bow. Working from a clean bench with good light saves you from losing small screws.

  • A bow sight with its mounting bracket and manufacturer’s hardware
  • A hex key set and a torque driver or torque-limiting wrench
  • A bubble level, ideally one that clips onto the sight or bracket
  • Thread locker in a low-strength formula, if the manufacturer recommends it
  • A bow stand or a sturdy holder, plus a target you can shoot at

Check your bow’s manual for the sight-mounting holes and any torque specifications. Many manufacturers list a specific torque range for the bracket bolts, so follow their numbers instead of guessing.

Step-by-Step: Mounting the Sight Bracket

  1. Choose the mounting position. Attach the bracket to the riser’s sight-mounting holes, usually at the front of the riser where your sight window lines up with the arrow shelf.
  2. Set the bracket loosely. Thread the bolts by hand first so the bracket can still shift slightly.
  3. Align the sight window. Center the sight so the arrow sits in the middle of the sight housing when you look through it at full draw.
  4. Level the sight. Place the bubble level on the sight housing or bracket and adjust until the bubble is centered. A tilted sight throws your vertical pin off at longer distances.
  5. Tighten to spec. Snug the bolts evenly, then tighten to the manufacturer’s torque value. Check the bracket once more after the first few shots.

Setting Height, Depth and Pin Alignment

Once the bracket is secure, fine-tune how the sight sits relative to your eye and the arrow. Most sights have adjustments for height and depth. Set them so the pins are visible without strain and the sight does not contact your arm or hand during the shot.

Quick alignment checks

  • Draw to your normal anchor point and confirm your eye sees the full sight window.
  • Look for the top pin to sit directly above the arrow path at close distance, with the other pins stacked below it.
  • Recheck the level after each adjustment, since moving the sight can shift it slightly.

Common Mistakes to Avoid

  • Tightening bolts past the torque spec, which can strip threads or crack the bracket
  • Skipping the level check and then chasing a group that drifts left or right
  • Setting the sight too close to the riser, so the bow hand or string contacts it
  • Forgetting to recheck bolts after the first session, when they often loosen slightly
  • Assuming a new sight is zeroed; you still need to sight in at your actual distances

If your groups look off after mounting, the cause is often not the sight. The guide Why Do Archery Attack Bows and Arrows Miss? 6 Causes and Fixes covers other common sources of misses, such as nocking point and release issues.

  • Bubble level for bow sights helps you confirm the sight sits square to the arrow path before you lock it down. View on Amazon
  • Hex key and torque wrench set for archery lets you tighten bracket bolts to the manufacturer’s specification instead of relying on feel. View on Amazon
  • Low-strength thread locker helps keep bracket bolts from backing out during shooting, when the manufacturer approves its use. View on Amazon

Tips for Better Results

FAQ

Do I need a bubble level to mount a bow sight?

A level is strongly recommended. A sight that sits even slightly off level shifts your vertical pins as distance changes, which makes accurate aiming harder.

How tight should bow sight bolts be?

Tighten them to the torque value in your sight or bow manual. If no value is listed, snug them firmly and check them often, since over-tightening can damage the threads or bracket.

Should I have a professional mount my sight?

Many shooters mount their own sights without trouble. If you are unsure about torque specs or your bow’s warranty terms, a qualified bow technician can check the installation for you.

Conclusion

Mounting a bow sight comes down to a secure bracket, a level sight, correct height and depth, and torque that matches the manufacturer’s spec. Take your time with each step and recheck everything after your first few shooting sessions. Once the sight is locked in, the next step is sighting it in at your real shooting distances.

Ethan Brooks

About Ethan Brooks

Ethan Brooks is part of our editorial team and reviews and edits our target archery guides, checking product details against manufacturer specifications and owner feedback.

About the author

Ethan Brooks
Ethan Brooks

Ethan Brooks writes reviews and buying guides for Archery Society.