We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

Bow Sight Set Up: A Step-by-Step Guide for Accurate Shooting

Learn bow sight set up step by step: mounting, leveling, pin alignment, and sight tuning at 20, 30 and 40 yards for tighter groups from your first session.

Updated November 2026

A bow sight set up is the process of mounting your sight, leveling it, aligning the pins with your arrow flight and tuning each pin to a known distance. Done correctly, it gives you a repeatable aiming reference so your groups tighten up instead of drifting. The steps below apply to most compound and recurve bows with a standard sight bracket.

What You Need Before You Start

Gather everything before you touch the bow. Working from a checklist prevents you from stopping halfway through to hunt for a hex key.

Shopping for one? See our guide: Arrow Rest Set Up: 5 Best Picks Compared for Recurve and Compound Bows.

  • Allen (hex) keys matching your sight and bracket hardware
  • A bubble level, either a small attachable level or a built-in sight level
  • A target at a known distance, starting at 20 yards
  • A tape measure or range markers
  • A bow stand or a second person to help hold the bow steady
  • Your arrows, tuned and fletched as you normally shoot them

Mounting and Leveling the Sight

Start by attaching the sight bracket to the riser. Most brackets have a set of holes or slots that let you move the sight up, down and side to side. Set it roughly centered over the arrow rest so the pins line up with your arrow path.

  1. Tighten the bracket bolts snug, but do not lock them fully yet.
  2. Place the level on the sight housing or the sight bar and adjust until the bubble is centered on both axes.
  3. Tighten the bolts completely, then check the level again. Bolts often shift the sight slightly when fully tightened.

Aligning the Pins and Tuning to Distance

Once the sight is level, you need the pins to match your actual arrow flight. The goal is a clean, centered group at the distance each pin is set for.

Set the First Pin at 20 Yards

Shoot a group of three to five arrows at 20 yards with the top pin. Adjust the pin’s position until the arrows land in the center of the target. Move the pin up to raise the impact point or down to lower it, and recheck after each adjustment.

Add the Remaining Pins

Move back to 30 yards and repeat the process for the second pin, then 40 yards for the third. Keep groups small before making each adjustment, because a single arrow can mislead you.

Pin Distance Adjustment goal
Top pin 20 yards Center group on the target
Middle pin 30 yards Center group on the target
Bottom pin 40 yards Center group on the target

If your arrows fly consistently left or right of the target center, the sight may need a horizontal adjustment, and your arrow rest may also need attention. The article on Nock on Arrow Rest: How to Set It Up Correctly for Clean Arrow Flight is a useful reference for checking how the arrow leaves the bow, since rest and nock position affect group placement.

Common Mistakes to Avoid

  • Skipping the level. A sight that sits even slightly off level shifts your impact point at every distance.
  • Adjusting pins after a single shot. Shoot full groups before changing anything.
  • Tightening bolts without rechecking the level afterward.
  • Setting pins with a bow that is not at its normal draw weight or string height.
  • Ignoring arrow tuning. Poor arrow flight will make pin settings look wrong even when the sight is correct.

A bubble level that attaches to the sight bar makes leveling far quicker than eyeballing it.

View on Amazon

A set of hex keys in the correct sizes for your bracket prevents stripped bolts during adjustments.

View on Amazon

A target stand that holds your target at a fixed height helps you keep groups consistent across distances.

View on Amazon

FAQ

How often should I redo my bow sight set up?

Recheck your sight whenever you change arrows, string, draw weight or rest position, and at the start of each season. Small changes in any of these can shift your pins.

Can I set up a sight without a level?

You can estimate level by eye, but a bubble level is far more reliable. Even a small tilt will cause consistent misses at longer distances.

Do I need a rangefinder for pin setup?

No. Marked range distances are enough for setting pins accurately. A rangefinder helps when you hunt or shoot unmarked terrain. If you are considering one, the guide Garmin Rangefinder Bow Sight: Setup, Calibration and Use Guide covers that setup.

Conclusion

A solid bow sight set up comes down to three things: a level sight, pins aligned with your arrow path, and each pin tuned at its own distance using full groups. Work through the steps in order and keep a notebook of your settings. If your groups still drift after tuning, check your arrow rest and nock position, and consult an experienced archery coach or pro shop for help with persistent problems.

Ethan Brooks

About Ethan Brooks

Ethan Brooks is part of our editorial team and reviews and edits our target archery guides, checking product details against manufacturer specifications and owner feedback.

About the author

Ethan Brooks
Ethan Brooks

Ethan Brooks writes reviews and buying guides for Archery Society.