Ravin R10 Arrow Rest: Setup, Tuning and Tips for Beginners
Learn how to set up, tune and troubleshoot the Ravin R10 arrow rest, with clear steps on mounting, timing and arrow clearance for better accuracy.
Updated November 2026
The Ravin R10 arrow rest is a drop-away style rest that mounts to your bow riser and supports the arrow until the shot, then gets out of the way. This guide walks you through mounting the R10, setting the arrow height and centershot, checking clearance, and tuning it so your arrows fly straight. Work through the steps in order and you will end up with a rest that holds arrows reliably and releases cleanly.
What You Need Before You Start
Gather these tools before you touch the bow. Having everything on hand keeps you from stopping halfway through a setup.
- A hex key set that matches the rest’s mounting hardware
- A bow square or straightedge for checking alignment
- A paper tuning tool or a bare-shaft tuning setup
- A small ruler or calipers for measuring arrow height
- A bow press or a stable bow stand
- Your arrows, already cut to the correct length and fitted with nocks
How to Mount the Ravin R10 on Your Bow
Mounting comes first because every later adjustment depends on the rest sitting square to the riser. Start by attaching the rest’s bracket to the riser’s mounting holes, keeping the hardware loose enough to slide.
- Position the rest so the arrow shelf sits just above the riser’s cutout.
- Set the rest at a rough height, roughly where the arrow shaft will sit when nocked.
- Check that the rest is level from side to side with your bow square.
- Tighten the mounting screws evenly, a little at a time, so the bracket does not cant.
Setting Arrow Height and Centershot
Arrow height controls how the arrow sits relative to the riser, and centershot controls how far the arrow sits from the bow’s center. Both affect how the arrow leaves the bow. Get these close before you move on to fine tuning.
Arrow Height
Set the arrow so it rests level with the centerline of the riser, or slightly below it, depending on your bow’s manufacturer guidance. Adjust the vertical slot on the rest, then recheck with a square. Small changes of about 1/32 inch make a noticeable difference.
Centershot
Place the arrow so the tip sits on or very near the bow’s center line. Slide the rest horizontally until the arrow lines up with the riser’s center. Lock the rest down after each change and check again.
Tuning the Ravin R10 for Clean Arrow Flight
Once the rest is mounted and roughly positioned, tuning confirms that the arrow leaves the bow without bumping the rest. Paper tuning is the most common starting point. Shoot an arrow through a sheet of paper held about three feet from the bow. A clean tear with the fletching centered means the arrow flies straight. A tear that shows the arrow’s nock side or a fishtail shape points to a tuning issue.
Adjust the rest’s tension and position in small steps. Make one change, shoot again, and compare. Working slowly is the fastest way to a reliable setup.
Common Mistakes to Avoid
- Tightening mounting screws unevenly, which pulls the rest out of square.
- Skipping the level check and relying on eye alone.
- Making several adjustments at once, so you cannot tell which one helped.
- Ignoring arrow clearance, which can cause the arrow to brush the rest on release.
- Using arrows with the wrong spine, which no rest adjustment can fully correct.
Recommended Gear
A bow square makes it easy to confirm the rest is level and aligned before you shoot. View on Amazon
A paper tuning kit gives you a repeatable way to check arrow flight after every change. View on Amazon
A bow press lets you safely adjust limb and cam components while the bow is stable. View on Amazon
If you are comparing this rest with other options, see Ravin Premium Arrow Rest Compared: 6 Best Picks for 2026 for a broader look at the line. For general background on how arrow holders work, What Holds Arrows in Archery: Quivers, Arrow Rests and Holders Explained covers the basics well.
FAQ
Do I need a bow press to set up the Ravin R10?
A bow press is not strictly required for mounting the rest, but it makes safe adjustment of the bow easier. If you have no press, use a stable stand and follow the manufacturer’s guidance on working with the bow.
How often should I recheck my tuning?
Recheck tuning after any change to the rest, arrows, or bow settings, and after any significant change in draw weight or string. Periodic checks help catch drift caused by loosened screws.
What if my arrows still fishtail after tuning?
Fishtailing often points to arrow spine, nock fit, or rest position rather than the rest alone. Recheck your arrow setup and make small adjustments to the rest before changing other parts.
Conclusion
With the rest mounted square, arrow height and centershot set, and paper tuning done, your Ravin R10 should release arrows cleanly. Make adjustments one at a time and recheck after each change. If your results still look off, consult an experienced archery shop or certified technician for help.
Related reading
- Zero Effect Arrow Rest: How It Works and How to Set One Up
- Whisker Biscuit Arrow Rest Installation: A Step-by-Step Guide
- Vapor Trail Gen 7 Arrow Rest Review: Key Features Explained
- Vapor Trail Arrow Rest Review: Pros and Cons
Ready to choose one?
