We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

Hoyt QAD Arrow Rest: Setup Steps and Tuning Tips for Clean Flight

Learn how to mount, set up and tune a Hoyt QAD arrow rest for clean arrow flight, with step-by-step tips on height, timing and common mistakes.

Updated November 2026

A Hoyt QAD arrow rest is a drop-away style rest that cradles the arrow until release and then falls out of the way. This guide walks you through mounting a Hoyt QAD arrow rest on a Hoyt bow, setting its position, and making basic adjustments so your arrows fly straight and quiet. You will need a few hand tools and about an hour of patient work.

Before You Start: Check Compatibility and Parts

Confirm that the rest matches your bow’s riser and mounting hole pattern. Hoyt risers vary by model year, so check the manufacturer’s spec sheet for your specific bow before buying or installing. Make sure you have the rest, its mounting hardware, the cables or spring included with that model, and a fresh rest pad or felt if the rest uses one. Read the instructions that came with the rest, because some QAD designs differ in cable routing.

Shopping for one? See our guide: 5 Best Drop Away Arrow Rest QAD Models for Target and Hunting (2026).

How to Mount a Hoyt QAD Arrow Rest

  1. Set the bow on a padded surface with the riser facing up and the string relaxed.
  2. Attach the rest body to the mounting holes on the riser using the supplied screws. Hand-tighten first so you can adjust position.
  3. Connect the cable or spring to the rest arm and to the cable guard or cam as the manufacturer diagrams show. Make sure the cable runs freely without rubbing the riser.
  4. Set the rest so the arrow shaft sits on the pad at the centerline of the bow. Tighten the screws fully once the position is right.

Setting Height and Centershot

Proper height places the arrow level with the nock point and in line with the string when at full draw. Start with the rest about a quarter inch below the arrow’s centerline, then raise it in small steps until the arrow sits level when nocked. Next, adjust the lateral position so the arrow sits in the center of the string at full draw. Most archers aim for a centershot value that keeps the arrow pointed straight at the target when viewed from behind the bow.

Checking Timing and Rest Movement

Draw and release slowly several times and watch the rest arm. It should fall away cleanly as the arrow leaves the string, without catching the fletching or pulling the arrow sideways. If the arm lags, check the cable tension and make sure the spring or cable is not binding.

Tuning for Clean Arrow Flight

Shoot a few arrows at a paper target from about 10 feet. Look at the tears left in the paper. A tear pointing up often means the arrow is too stiff, while a tear pointing down suggests it is too weak. Adjust the rest height or lateral position in small increments and retest. Bare-shaft tuning, where you shoot an unfletched arrow and compare its flight to a fletched one, is another useful check, though it requires a clear shooting lane.

Common Mistakes

  • Tightening the mounting screws before setting position, which makes fine adjustment difficult.
  • Letting the cable rub the riser or bowstring, which causes erratic rest movement.
  • Setting height by eye without checking the nock point, leading to inconsistent groups.
  • Ignoring worn felt or pads, which can cause arrows to skip or wobble on release.
  • Making large adjustments at once instead of small changes you can test one at a time.
  • Bow square and nock point tool: A bow square helps you check arrow alignment and nock placement, making rest setup more consistent. View on Amazon
  • Paper tuning kit: A paper tuning frame lets you see arrow flight angle clearly during adjustment. View on Amazon
  • Replacement rest pads: Fresh felt or pads keep the arrow seated consistently after the rest is tuned. View on Amazon

For related setup guidance, see QAD UltraRest Integrate MX Arrow Rest: Setup, Tuning and Buying Tips and Hoyt Ultrarest Integrate Mx2 Arrow Rest: Setup, Tuning and Buying Guide. If you are replacing worn parts, QAD Arrow Rest Replacement Felt: Step-by-Step Guide for Clean Arrow Flight covers that process.

FAQ

How often should I check my Hoyt QAD arrow rest settings?

Check the mounting screws, cable tension and rest position after the first few sessions, then every month or after any change in arrow weight or bow draw. Regular checks prevent gradual drift that affects accuracy.

Can I use a Hoyt QAD rest on a different bow brand?

It depends on the riser’s mounting pattern and the rest’s design. Check the manufacturer’s compatibility information before installing on a non-Hoyt bow.

Do I need a professional to set up my rest?

Many archers set up their own rests with basic tools, but a certified archery technician can help if you are struggling with tuning or if the bow is valuable. Consult a qualified shop if you are unsure about cable or cam work.

Conclusion

A properly mounted and tuned Hoyt QAD arrow rest supports consistent release and clean arrow flight. Work through mounting, height and centershot in small steps, and test after each change. Good setup habits will pay off with tighter groups.

Ethan Brooks

About Ethan Brooks

Ethan Brooks is part of our editorial team and reviews and edits our target archery guides, checking product details against manufacturer specifications and owner feedback.

About the author

Ethan Brooks
Ethan Brooks

Ethan Brooks writes reviews and buying guides for Archery Society.