How to Make a Leather Archery Arm Guard: A Step-by-Step Guide for Beginners
Learn how to make a leather archery arm guard at home: measure your forearm, cut and shape the leather, attach it securely, and protect your arm from string sla
Updated November 2026
Learning how to make a leather archery arm guard takes an afternoon and a few basic tools. By the end, you will have a guard sized to your forearm, shaped to sit over the inside of your bow arm, and fastened so it stays put through a full shooting session. Leather is the classic material because it is tough, flexible once broken in, and quiet when the string hits it.
Measure Your Forearm and Mark the Pattern
Start by measuring your bow arm from the wrist to just below the elbow, then measure the circumference at the widest point of your forearm. Add about 1 inch to the circumference so the guard wraps comfortably without cutting into your skin. Most guards run 6 to 8 inches long for target shooting, but many archers prefer a longer guard for extra coverage. A Archery Arm Guard Pattern: How to Choose or Make the Right One can help you settle on a shape before you cut.
Shopping for one? See our guide: 4 Best Archery Leather Arm Guard Options for Target Archers (2026). We also found Bike Helmet Chin Guard: How to Choose, Fit and Use One Safely useful on this point.
Lay a sheet of paper on the leather or a piece of scrap cardboard, then trace a rectangle matching your length and circumference. Round the corners slightly so the edges will not dig in during the draw. Cut the template out and test it on your arm before cutting the leather.
Cut, Shape and Prepare the Leather
Use 2 to 3 millimeter vegetable-tanned leather, which holds a curve well and softens with use. Trace the template onto the leather’s flesh side, then cut with a sharp utility knife or leather shears. Punch holes about 1/2 inch from each edge, spaced every 1 to 1.5 inches, so you have a clean pattern for lacing or stitching. Dampen the leather lightly and wrap it around your forearm, then let it dry in that shape. This molds the guard to your arm and keeps the inside curve smooth.
Attach the Guard Securely
There are two common fastening methods. The first is a lace-up closure: thread a 1/8-inch leather cord through the punched holes and tie it snugly, leaving a small loop so you can adjust tension. The second is a strap-and-buckle closure, where you sew a short leather strap to one edge and a buckle to the other. Either way, the guard should stay in place when you bend your arm, but you should still be able to slide it on and off with one hand. Stitch any seams with waxed thread and a saddle stitch so they hold under repeated tension.
Tools and Materials Checklist
- 2 to 3 mm vegetable-tanned leather, large enough for your pattern
- Measuring tape and a pencil or marker
- Sharp utility knife or leather shears
- Hole punch or awl, plus a cutting mat
- Waxed thread and two needles, or 1/8-inch leather lace
- Small buckle and strap, if using a buckle closure
- Water spray bottle for shaping
Common Mistakes and Tips
- Cutting before measuring the wrap. A guard that is too tight will pinch the forearm and restrict blood flow.
- Using leather that is too thin. Thin hide tears under string impact and loses its shape quickly.
- Skipping the shaping step. A flat guard will shift during the shot; molding it to your arm prevents this.
- Placing the closure directly under the string path. Keep fasteners on the outside edge so they do not catch the string.
- Forgetting to test the fit at full draw. Check that the guard stays flat and covers the forearm when you anchor.
Recommended Gear
A good leather cutting mat protects your work surface and makes it easier to cut straight lines. View on Amazon
Waxed thread designed for leather stitching holds saddle stitches better than standard thread. View on Amazon
FAQ
What leather works best for a DIY arm guard?
Vegetable-tanned leather between 2 and 3 millimeters thick is the most common choice. It holds a curve, resists abrasion, and softens gradually with use.
How long should the guard be?
Most target archers use a guard about 6 to 8 inches long. Longer guards give more coverage, so you can adjust the length to suit your form and clothing.
Can I make the guard without sewing?
Yes. A guard with a lace-up or buckle closure needs no stitching at all, though sewn seams last longer under repeated string contact. Consult an experienced archery coach if you are unsure about fit or setup.
Conclusion
Measuring carefully, cutting clean and shaping the leather to your forearm gives you a guard that fits and lasts. Test the fit at full draw before you shoot a full session. A well-made guard protects your arm and keeps your attention on your form.
Related reading
- Leather Archery Arm Guard UK: How to Choose, Fit and Care for One
- Archery Arm Guard Pattern Free: How to Make Your Own Step by Step
- Women's Archery Arm Guard: How to Choose and Fit One Properly
- Make Leather Arm Guard: 6 Best Picks for Archers (2026)
Ready to choose one?
