We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

How to Install a Drop Away Arrow Rest: 6 Steps for a Quiet, Clean Shot

Learn how to install a drop away arrow rest in six clear steps, from mounting and cable setup to timing and checking clearance, so your arrow flies true.

Updated November 2026

To install a drop away arrow rest, you mount the rest on your bow’s riser, attach the cable and cable guard, set the rest height and centershot, then check that the arrow lifts off the rest cleanly at full draw. Done right, the rest holds your arrow steady until release and then drops out of the way before the arrow passes it. The whole job takes most archers under an hour once they have the right tools on hand.

What You Need Before You Start

Gather everything before you touch the bow. Most installs stall because a screw or cable part is missing.

Shopping for one? See our guide: Drop Away Arrow Rest: 5 Best Picks Compared for Compound Bows (2026).

  • Allen wrenches in the sizes your rest specifies (commonly metric)
  • A cable-compatible rest with its mounting plate, pivot bracket and spring
  • A bow square and a tape measure
  • Blue thread locker for the mounting screws
  • Your bow’s manual or the manufacturer’s setup specs

Step-by-Step Installation of a Drop Away Arrow Rest

Step 1: Mount the Rest Base

Fit the rest’s mounting plate to the riser’s arrow rest holes. Leave the screws finger-tight so you can still adjust the position. Use a small dab of thread locker only after you have finalized the setting.

Step 2: Attach the Cable and Pivot Bracket

Connect the rest’s pivot arm to the cable using the included clamp or cable-end fitting. Snug the cable guard so the cable runs parallel to the riser’s cable slot. A cable that rubs or twists will change the rest’s timing.

Step 3: Set Rest Height and Centershot

Set the rest so the arrow’s centerline sits level with your nock point, generally about one-quarter to one-half inch below the center of the arrow’s nock at full draw, depending on your bow’s setup guide. Then move the rest left or right until the arrow sits centered over the riser, using a bow square to confirm the placement.

Timing and Clearance Checks

Step 4: Check the Drop Timing

Draw the bow slowly and watch the rest. The arm should begin to drop just as the bow reaches full draw, with the cable pulling the rest down before you release. If it drops early, shorten the cable slightly; if it lags, lengthen it. Make small adjustments and re-check after each one.

Step 5: Confirm Arrow Clearance

Nock an arrow and release it slowly while watching the rest. The arm should be fully clear of the arrow’s path before the fletching passes. Look for any contact on the fletching, which can cause erratic flight. Recheck clearance after every timing adjustment.

Step 6: Tighten and Test

Once timing and clearance are right, tighten all screws to the torque or snugness your manual specifies and apply thread locker. Shoot a few arrows at close range, then check the paper or target for grouping. If the arrows group left or right, recheck centershot before changing anything else.

Common Mistakes

  • Tightening screws before the timing is set, which makes later adjustments hard.
  • Letting the cable twist, which causes inconsistent drop.
  • Skipping the clearance check, leaving fletching to brush the rest.
  • Mounting the rest without checking the riser’s hole pattern for your specific bow.
  • Forgetting to recheck timing after a string change or new cable.
  • Bow square: Makes centershot and rest alignment far easier to verify. View on Amazon
  • Blue thread locker: Keeps mounting screws from loosening during shooting. View on Amazon
  • Allen wrench set: A metric set covers most rest mounting hardware. View on Amazon

FAQ

How long does it take to install a drop away arrow rest?

Most archers finish a first install within an hour. Timing adjustments can add time if the cable needs several small changes.

Do I need a bow press to install a drop away rest?

Not for most rests, since the cable mounts without removing the string. Always follow your bow manufacturer’s guidance on safe handling.

How do I know if my drop away rest timing is right?

The arm should drop just as the bow reaches full draw and clear the arrow before release. If the arrow hits the rest or fletching, adjust the cable and recheck.

Conclusion

Mount the rest, set the cable, then fine-tune height, centershot and timing in that order. Check clearance with a slow dry draw and a few test shots before you trust the setup. If something still feels off after that, a qualified archery pro shop can check your bow in person.

Ethan Brooks

About Ethan Brooks

Ethan Brooks is part of our editorial team and reviews and edits our target archery guides, checking product details against manufacturer specifications and owner feedback.

About the author

Ethan Brooks
Ethan Brooks

Ethan Brooks writes reviews and buying guides for Archery Society.