We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

How to Install Arrow Rest Recurve: A Step-by-Step Guide for Beginners

Learn how to install arrow rest recurve on your bow in clear steps, with tips on positioning, tightening and checking your setup before you shoot.

Updated November 2026

Learning how to install arrow rest recurve bow setups is one of the first skills that improves your accuracy. A properly mounted rest holds the arrow steady as it leaves the string, and a correct position keeps the shaft clear of the riser. This guide walks you through the tools you need, the mounting steps and the checks that confirm the rest is ready to shoot.

What You Need Before You Start

Gather everything before you touch the bow. Most recurve rests mount into threaded holes in the riser, and the hardware usually comes with the rest. Keep the bow unstrung while you work.

Shopping for one? See our guide: 6 Best Bow and Arrow Rests for Recurve and Traditional Bows (2026).

  • The arrow rest, with its mounting screws and any shims or spacers
  • A hex (Allen) key set that matches the screw sizes
  • A bow square or a clean ruler for measuring center shot
  • Painter’s tape or a soft cloth to protect the riser finish
  • A marker for noting your starting positions

Step-by-Step: Mounting the Rest

  1. Remove the old rest and clean the mounting area. Wipe off grease or residue so the new rest seats flat against the riser.
  2. Attach the rest loosely. Start both screws by hand, then leave them slightly loose. This lets you slide the rest into position.
  3. Set the vertical height. Place an arrow on the rest and sight down it. The arrow should sit level with the string at full draw, or in line with the manufacturer’s stated starting height.
  4. Set the horizontal position (center shot). Measure from the string to the riser’s center point. Most beginners start with the arrow tip close to the riser’s center line, then adjust during tuning.
  5. Tighten the screws evenly. Snug one screw, then the other, alternating until both are firm. Do not overtighten, since stripped threads on a riser are costly to repair.
  6. Check the rest’s clearance. Draw the bow slowly and watch the arrow fletching pass the rest. Nothing should rub or catch.

Setting Up for Accuracy

A rest that is mounted correctly still needs to be tested. Shoot a few arrows at a close target, about 10 to 15 yards, and note where they land. If the groups drift left or right, move the rest in small steps, usually a quarter turn of the adjustment or a fraction of a millimeter at a time. Retighten after every change and retest before you move on.

Check the nock point and arrow fit as you go, since a rest that works with one arrow length or spine may need small changes with another. If you are unsure about tuning a bow that has a limited draw weight or a damaged riser, have a qualified archery technician inspect it before adjusting the hardware.

Common Mistakes

  • Tightening the screws before confirming the height and position, which forces you to strip the threads when you adjust.
  • Skipping the clearance check, so the fletching brushes the rest on every shot.
  • Mounting the rest on a riser that has a rough or greasy surface, which lets it shift under string tension.
  • Changing several settings at once, making it impossible to tell which change helped.
  • Ignoring the manufacturer’s starting measurements for your bow model.
  • Bow square: A square with a rule helps you measure center shot quickly and consistently. View on Amazon
  • Hex key set: A full set with the sizes your rest uses prevents rounded screw heads. View on Amazon

For more detail on a specific rest type, see Arrow Rest Stick On: How to Install a Stick-On Rest in 6 Steps or Arrow Rest Set Up: 5 Best Picks Compared for Recurve and Compound Bows. If you are choosing a rest before you install it, 7 Best Arrow Rests for Recurve Bows of 2026: Buyer's Guide compares the main styles.

FAQ

Do I need to unstring the bow to install an arrow rest?

Yes, unstring the bow before mounting or adjusting the rest. This keeps the riser free of string tension and makes it safe to work on the screws.

How do I know if my arrow rest is centered?

Measure from the string to the riser’s center line and compare that with the manufacturer’s starting figure. Final centering is confirmed by shooting groups and adjusting until the arrows land cleanly.

Can I install a recurve arrow rest myself?

Most archers can mount a rest with basic hand tools. If the riser is damaged or you are unsure about the threads, ask a qualified archery shop or technician to help.

Conclusion

Installing a recurve arrow rest comes down to clean mounting, careful height and position settings, and a clearance check before you shoot. Once the rest is in place, test with short-range groups and adjust one change at a time. Patience during setup pays off in tighter groups and fewer frustrating misses.

Ethan Brooks

About Ethan Brooks

Ethan Brooks is part of our editorial team and reviews and edits our target archery guides, checking product details against manufacturer specifications and owner feedback.

About the author

Ethan Brooks
Ethan Brooks

Ethan Brooks writes reviews and buying guides for Archery Society.