Full Length Archery Arm Guard Pattern: Step-by-Step Cutting Guide
Learn how to use a full length archery arm guard pattern to cut, fit and shape a forearm guard that covers your wrist to elbow. Clear steps for target archers.
Updated November 2026
A full length archery arm guard pattern gives you a template for cutting a forearm guard that covers the bowstring side of your arm from wrist to near the elbow. With the right pattern, you can cut the leather once, fit it to your own measurements, and end up with a guard that stays in place during a full shooting session. This guide walks through measuring, transferring the pattern, cutting and final fitting.
Measure Your Forearm Before You Cut
Start with your arm measurements, because a full length guard that fits your forearm will protect better than a generic one. Stand with your bow arm extended and take three measurements, then add a little room on each one.
- Wrist to elbow length: Measure along the outside of your forearm from the wrist bone to the crease of the elbow.
- Forearm circumference at the widest point: Wrap a soft tape around the thickest part of your forearm, usually just below the elbow.
- Wrist circumference: Measure just above the wrist bone where the guard will sit.
Most archers add about half an inch to the circumference measurements so the guard does not feel tight when you draw. Check the length against your draw and string path before you commit to a final size.
Transfer and Adjust the Pattern
Print or trace your full length archery arm guard pattern at 100 percent scale, and check the printed scale bar against a ruler before you use it. Compare the pattern length and width with your measurements. If the pattern is longer than your wrist-to-elbow measurement, shorten it at the top edge, not the bottom, so the wrist coverage stays correct.
Next, mark the strap and buckle positions. Most patterns place two or three straps along the wrist and forearm. Mark each strap location on the pattern and confirm that the straps will land on the outside of the arm, away from the string.
Cut, Shape and Mark the Leather
Lay the pattern on the leather, grain side up, and trace around it with a fine-tipped awl or chalk marker. Cut with a sharp utility knife or leather shears, working in long, smooth strokes. Keep the cut edges square to the leather surface so the guard lies flat.
After cutting, dampen the leather lightly and wrap it around your forearm to test the curve. Some archers also mark a small line along the inside edge where the bowstring will pass, so they can check for clearance during the first few shots.
Fit, Test and Adjust the Guard
Attach the straps and fasten the guard on your arm, then draw and release several arrows at a low draw weight. Watch for three things: the string should not slap the leather, the guard should not shift during the release, and the wrist area should not press into your skin. Adjust strap tension and position until all three are correct.
Leather stretches and dries over time, so recheck the fit after your first few sessions. Mark any new adjustments on the pattern so you can reproduce the fit later.
Recommended gear
- A cutting mat and a sharp utility knife give clean, straight edges on the leather, which makes the final fit more predictable. View on Amazon
- A leather punch set lets you place strap holes accurately so the guard sits where you planned. View on Amazon
Common mistakes to avoid
- Skipping the scale check on the printed pattern, which can throw off the length by a noticeable amount.
- Cutting the guard too tight, which restricts the forearm and makes the draw feel awkward.
- Placing straps on the string side of the arm, where they can catch the bowstring.
- Failing to test the fit at a low draw weight before shooting at full strength.
If you are unsure about your measurements or fit, consult an experienced archery coach or a local archery shop for hands-on help.
For more background, see Archery Arm Guard Pattern: How to Choose or Make the Right One and Leather Arm Guard Pattern: Step-by-Step Guide to Cutting and Fitting One. If you want a ready-made option instead, Archery Full Length Arm Guard: 4 Best Picks for Target Archers (2026) compares several full length models.
FAQ
How long should a full length arm guard be?
It should cover the forearm from near the wrist to close to the elbow crease without touching the crease when you bend your arm. Measure your own wrist-to-elbow length and compare it to the pattern before cutting.
Can I use the same pattern for both arms?
Not directly. Your bow arm and drawing arm differ, and the guard is only worn on the bow arm, so make one pattern for the arm you shoot with.
How do I know if the guard fits correctly?
It should stay in place during the draw and release, let the string clear without slapping, and feel comfortable at full draw. If any of these fail, adjust the straps or the cut before shooting more.
Conclusion
A full length archery arm guard pattern works best when you measure your own arm, adjust the template before cutting and test the fit slowly. Take your time with the strap placement, because that step decides how well the guard stays put. Once the fit is right, the guard should protect your forearm without getting in the way of your shot.
Related reading
- Extra Long Archery Arm Guard: How to Choose the Right Length and Fit
- Archery Arm Guard Pattern Free: How to Make Your Own Step by Step
- Archery Arm Guard Leather Pattern: A Practical Guide (2026)
Ready to choose one?
