We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

Cbe Trek Bow Sight: How to Choose, Set Up and Use It (Step by Step)

Learn what a cbe trek bow sight is, how to set it up, adjust pins and sight in for accurate shots, with practical steps for new archers.

Updated November 2026

A cbe trek bow sight is a bow-mounted aiming device that gives you a fixed reference point for each shot distance. This guide explains what to check before you buy or mount one, how to set it up on your bow, and how to sight it in so your arrows land where you aim. Work through the steps in order and you will have a sight that holds its zero from session to session.

What to Check Before You Mount a cbe trek bow sight

Start by confirming the sight matches your bow setup. Check the mounting method, the riser or accessory bracket it attaches to, and whether it fits your bow’s hand orientation. Manufacturers usually list compatible bow types and mounting hole patterns, so compare those specifications against your bow before you start drilling or tightening anything.

Shopping for one? See our guide: Bow Sights with Rangefinder: 5 Best Picks Compared (2026).

Next, decide how you will shoot. Most sights work best with a consistent anchor point, a steady draw length and a release technique you repeat every time. If your form changes from shot to shot, the pins will move with it, and sighting in will feel frustrating. Fix form first, then sight in. You can read more about setup basics in our guide to Garmin Rangefinder Bow Sight: Setup, Calibration and Use Guide.

How to Mount and Set Up the Sight

Mount the sight on the bow with the hardware the manufacturer includes. Snug the fasteners evenly, but do not overtighten them. Overtightening can strip threads or warp a bracket, which causes the sight to drift.

  1. Clamp the sight bracket to the riser and tighten lightly.
  2. Set the sight so the pin guard or housing sits square to the arrow path.
  3. Check that the sight does not contact the arrow fletching or the rest at full draw.
  4. Tighten all fasteners to the torque value listed in the manual, then recheck after your first few shots.

Confirm clearance at full draw before shooting. A pin housing that touches the fletching can change arrow flight and cause injury.

How to Sight In a cbe trek bow sight

Sighting in means adjusting each pin so the arrow strikes where the pin points at a known distance. Use a target at a measured distance, such as 20 yards, and shoot from a stable stance.

Set the Starting Position

Adjust the sight housing so the pins sit roughly centered in the bow’s sight window. Shoot three or four arrows at your first distance. Group them first, then adjust the pin to the group center, not to any single arrow.

Adjust the Pins

Move the pin in the direction of the impact. If arrows land high, lower the pin. If they land left, move the pin right. Make small changes, usually a quarter turn or less, then shoot another group. Repeat until the group is centered on the aiming spot.

Repeat for Each Distance

Move the target to your next distance and repeat the process. Record the pin settings at each distance on a card or in a notebook. Many archers mark the pin positions directly on the sight housing with a fine marker for quick reference.

Common Mistakes to Avoid

  • Sighting in while tired or with inconsistent form, which makes the pins chase every shot.
  • Adjusting the pin after a single bad arrow instead of looking at the group.
  • Skipping the post-shot recheck of mounting hardware.
  • Changing the draw weight, arrow length or release without re-sighting afterward.
  • Shooting at unmeasured distances, which makes the pin settings unreliable.

A stable target stand keeps your sighting distances consistent, which matters when you are making small pin adjustments. View on Amazon

A bow square or a fine-tip marker helps you record pin positions and check that the sight sits square to the arrow path. View on Amazon

A laser or sight-in tool can speed up the initial alignment on the riser, though you should still confirm results with real arrows. View on Amazon

FAQ

How often should I check the sight alignment?

Check alignment before each session, especially after transporting the bow. Vibration and bumps can shift the housing over time.

Why do my arrows still group off-center after sighting in?

Inconsistent anchor, release or grip is the most common cause. Refine your form at a short distance before making further pin changes.

Should I consult a professional for installation?

If you are unsure about mounting hardware or torque values, ask a qualified archery pro shop to check the setup. A professional check is a sensible step if the bow is new to you.

Conclusion

A cbe trek bow sight is only as accurate as the setup behind it. Confirm compatibility, mount it squarely, and sight in at measured distances using consistent form. Record your pin positions and recheck them regularly, and the sight will stay reliable as you practice.

Ethan Brooks

About Ethan Brooks

Ethan Brooks is part of our editorial team and reviews and edits our target archery guides, checking product details against manufacturer specifications and owner feedback.

About the author

Ethan Brooks
Ethan Brooks

Ethan Brooks writes reviews and buying guides for Archery Society.