Bow Sight Adjustment Up or Down: A Step-by-Step Guide for Beginners
Learn how to decide whether to move your bow sight adjustment up or down, with a simple test, clear steps and common mistakes to avoid for tighter groups.
Updated November 2026
Bow sight adjustment up or down comes down to one question: is your arrow landing high or low on the target at the distance you’re shooting? Once you know which way the group is off, you can move the pin or sight housing the right direction and keep your shots on target. This guide shows you how to read your grouping, make the change, and confirm it with a few more arrows.
Read Your Groups Before You Touch the Sight
Shoot three to five arrows at a single distance, such as 20 yards, from a steady, rested position. Look at where the arrows land as a group, not as individual holes. The center of that group tells you what the sight needs. If the center sits above the bullseye, the sight needs to move down. If it sits below, move the sight up. If the group is wide and scattered, fix your form first, because sight changes will not cure a shooting problem.
Shopping for one? See our guide: Bow Sights with Rangefinder: 5 Best Picks Compared (2026).
Make the Adjustment in the Correct Direction
Sight movement is the opposite of arrow movement. This is the step where most beginners go wrong, so keep it in mind:
- Arrows hitting high: Move the pin or sight down, so the sight aims lower and the arrow lands lower.
- Arrows hitting low: Move the pin or sight up, so the sight aims higher and the arrow lands higher.
- Arrows hitting left or right: Adjust windage in the same logic. Move the sight in the direction you want the arrows to go.
Make small changes. A common starting point is a few clicks or a small turn on the elevation knob, then shoot another group before changing anything else. Large adjustments often overshoot the target and waste time.
Adjust Elevation Across Multiple Distances
A sight is set for one distance at a time. Work through your shooting distances in order, usually 10, 20, and 30 yards, and record the setting for each. Many archers keep a small log with the distance, the sight setting, and the date. Check your manufacturer’s manual for the exact elevation scale, since the number of clicks per movement varies by model. For setup on specific designs, you can also review guides such as Bow Sight Set Up: A Step-by-Step Guide for Accurate Shooting and Bow Sight Pin Adjustment: A Step-by-Step Guide for Beginners.
Confirm Each Change
After each adjustment, shoot another group of three to five arrows from the same spot. The new group should center on your aiming point. If it moves past the target, reverse course slightly. Do not chase single arrows, since one shot can be a bad release rather than a sight problem.
Checklist for Sight Adjustment
- Confirm your form is consistent and your grip is repeatable.
- Shoot a group of three to five arrows at one distance.
- Find the center of the group and note whether it is high, low, left, or right.
- Move the sight in the opposite direction of the arrow group.
- Shoot a new group and repeat until the center matches your aim point.
- Record the setting for that distance and move to the next one.
Common Mistakes
- Moving the sight in the same direction as the arrows, which makes the problem worse.
- Making large changes instead of small, measured ones.
- Adjusting after a single arrow rather than a full group.
- Tuning the sight while the bow is loose, the rest is shifting, or your anchor changes.
- Forgetting to write down settings, so you have to start over next session.
FAQ
If my arrows hit high, do I move the sight up or down?
Move the sight down. The sight aims lower, so the arrow lands lower and closer to your aim point.
How many arrows should I shoot before making a change?
Shoot three to five arrows as a group. A single arrow can be affected by release or form, so it does not show the true setting.
Can I fix a bad group by adjusting the sight?
Not if the group is wide and scattered. That usually points to shooting form, anchor, or release. Fix those first, then tune the sight.
Conclusion
Bow sight adjustment up or down depends on where your group center sits compared with your aim point. Move the sight opposite to the arrows, make small changes, and confirm each one with a fresh group. Keep a log for each distance, and your sight settings will become a reliable reference for every session.
Related reading
- What Is a Sight Master Bow Sight and How Do You Set One Up?
- Triple Stack Bow Sight: How to Set Up and Sight In a Three-Pin Sight
- React H4 Bow Sight: What It Is and How to Set One Up
- Lens for Bow Sight: How to Choose and Set One Up (Step by Step)
Ready to choose one?
