We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

Arrow Keeps Falling Off Rest? 6 Causes and Fixes for Beginners

Arrow keeps falling off rest? Learn the common causes, from timing and nock fit to rest tension, and the fixes that keep your arrow seated at full draw.

Updated November 2026

If your arrow keeps falling off the rest, the cause is almost always one of a few setup problems: the rest is set at the wrong height or angle, the arrow is not seating properly on the nock, the rest tension is off, or the arrow is being pushed sideways at release. This guide walks through how to check each of these in order so you can get a secure arrow pass and a clean shot.

Check the Rest Height and Centershot First

Start with the rest position, because a rest set too high or too low will let the arrow roll off before or during the shot. Set the arrow so the shaft sits level with the arrow centerline and the fletching clears the riser without rubbing. Most rests are adjusted with a small set of screws or a height dial, so make small changes of a quarter turn at a time and retest after each adjustment.

Shopping for one? See our guide: Arrow Rest for Compound Bow: 6 Best Picks Compared (2026).

Centershot matters too. If the rest sits too far to one side, the arrow tends to slide off that side when you release. Measure from the riser to the shaft at the nock end and the tip end; both measurements should be close to equal for a neutral setup.

Confirm the Nock Fit and Nock Height

A loose or poorly seated nock can let the arrow drop off the rest even when everything else is correct. Make sure the nock snaps onto the string with a firm click and does not wobble. Nock height should also be consistent: if the nock sits too high or too low on the string, the arrow can sit at an angle on the rest and slip. Use a nock height tool or a nock set (a small clamp or wire) to keep nock placement repeatable.

Adjust Rest Tension and Arrow Pass

Many drop-away and launcher-style rests use spring tension to hold the arrow on the rest until the bow is drawn. If that tension is too light, the arrow can fall off during the draw or at anchor. If it is too heavy, the arrow may not drop cleanly on release, which can cause erratic flight. Adjust tension in small increments and shoot a few arrows at each setting to check how the arrow stays put.

Pay attention to arrow pass too. Some rests use a flexible arm or a whisker-type design that holds the arrow in place only while the bow is at rest. Owners often report that worn or bent arms are the cause of a sudden change in hold. Inspect these parts for wear and replace them when they lose their spring.

Check Your Shooting Form

Sometimes the rest is fine and the problem is in how you release. Plucking, torquing the bow, or pulling the string off to one side will push the arrow off the rest. Keep your grip relaxed and your bow arm steady, and let the string move straight back. A clean release helps the arrow stay on the rest and leave the bow smoothly.

Quick Setup Checklist

  1. Set rest height so the arrow sits level with the centerline.
  2. Check centershot on both ends of the arrow.
  3. Confirm the nock clicks firmly onto the string.
  4. Adjust nock height so the arrow sits square on the rest.
  5. Set rest tension in small steps and test at full draw.
  6. Inspect the rest arm or whisker for wear.

Common Mistakes

  • Changing several settings at once, which makes it hard to tell what fixed the problem.
  • Ignoring a worn nock or a cracked nock point, which can cause the arrow to sit crooked.
  • Assuming tension is the only factor when height or centershot is actually off.
  • Skipping a retest after every adjustment.
  • Overtightening screws, which can strip threads or bend the rest mount.

A nock height tool helps you keep nock placement consistent, which reduces arrow drop caused by an angled arrow. View on Amazon

A small set of hex keys and a fine-tip screwdriver makes rest adjustments easier without rounding the screw heads. View on Amazon

FAQ

Why does my arrow fall off the rest only when I draw the bow?

This usually points to rest tension or a rest arm that has lost its spring. Increase tension slightly or inspect the arm for wear.

Can a worn nock make the arrow fall off the rest?

Yes. A loose or damaged nock can let the arrow sit crooked, so the arrow may slip off the rest on release. Replace worn nocks and check the fit.

How do I know if the rest height is wrong?

If the arrow sits visibly above or below the centerline when nocked, or the fletching rubs the riser, the height is off. Adjust in small steps and recheck. If problems continue, consult a qualified archery pro shop.

Conclusion

Most arrow drop problems come from height, centershot, nock fit or tension, so work through those in order rather than changing everything at once. Make one adjustment at a time and test at full draw. If you keep losing arrows despite careful setup, have a local archery shop check your equipment.

Ethan Brooks

About Ethan Brooks

Ethan Brooks is part of our editorial team and reviews and edits our target archery guides, checking product details against manufacturer specifications and owner feedback.

About the author

Ethan Brooks
Ethan Brooks

Ethan Brooks writes reviews and buying guides for Archery Society.