How to Adjust Bow Sight If Shooting High: 5 Steps to Lower Your Arrows
Learn how to adjust bow sight if shooting high with five clear steps covering pin position, sight tape, and checking your form before you change anything.
Updated November 2026
If your arrows keep landing above the target center, you can usually fix the problem by lowering your sight pin or adjusting the sight housing. This guide shows you how to adjust bow sight if shooting high, starting with a quick check of your shooting setup so you change the right thing. By the end, you will have a repeatable process for bringing your groups back to the center.
Confirm the Problem Is Your Sight, Not Your Form
Before touching the sight, shoot a three-arrow group at a fixed distance, such as 20 yards, and note where the arrows land. Some high shots come from form issues like a collapsing bow hand or excessive pressure on the grip, which move the arrow up without any sight change. If your groups are tight but sit consistently high, the sight is the likely cause. If they scatter widely, work on your anchor and release first.
Shopping for one? See our guide: Bow Sights with Rangefinder: 5 Best Picks Compared (2026).
Adjust the Sight Pin Position
Most sight problems are solved by moving the pin down relative to the target. Here is the general process:
- Set up a target at a known distance and shoot a group of at least three arrows.
- Measure how far the group center sits above your aim point.
- Loosen the sight housing or pin locking screws slightly, following your sight manufacturer’s guidance.
- Move the pin down a small amount, then tighten the screws.
- Shoot another group and compare. Repeat until the arrows land near the center.
Make small changes. Moving a pin a quarter-inch at close range can shift your impact by several inches at longer distances, so work in increments and retest after each one.
Use Sight Tape or Yardage Settings
Many sights use a tape or a dial for each distance. If you shoot high only at longer yardages, the problem may be the setting for that distance rather than the whole sight. Check your tape: if the 40-yard mark is too low on the tape, your arrows will sail over the target at that range. Re-sight each distance you shoot, and mark your tape or dial so you can return to the correct setting quickly. For specific sight types, see Single Pin Dial Bow Sight: How to Set Up and Sight In for Beginners or Single Pin Bow Sight Tape: How to Set Up and Use One Correctly.
Check Your Sight Alignment and Mounting
A loose or tilted sight can throw your vertical aim off. Tighten the mounting bolts, then confirm the sight is level with the arrow shaft when the bow is drawn. A sight that sits tilted can make high or low shots appear to be a yardage problem. If the sight keeps shifting, the mount or bracket may need attention. Peep Sight on Bow Keeps Twisting? How to Fix It Step by Step covers a related alignment issue that can affect your aim.
Common Mistakes
- Changing several settings at once, which makes it impossible to tell which change helped.
- Adjusting the sight based on one arrow instead of a group of three or more.
- Forgetting to re-sight after changing your draw length, arrow weight, or string.
- Ignoring anchor point consistency, which can mimic a sight problem.
- Shooting from a different distance than the one you used to set the sight.
Recommended Gear
- Sight tape or marking tools help you record settings for each distance so you can return to them without guessing. View on Amazon
- Bow sight wrench set gives you the correct size for adjusting pin housings and mounting bolts without stripping screws. View on Amazon
- Target stand with a face at fixed distance makes repeatable groups easier to measure. View on Amazon
FAQ
Should I lower the pin or raise the sight to fix high shots?
Lowering the pin is the usual fix, since moving the pin down brings the point of impact down. Raising the whole sight would have the opposite effect of what you need in most cases.
How many arrows should I shoot before adjusting?
Shoot at least three arrows at one distance and look at the group center. A single arrow can mislead you because of a small release error.
Can a sight that is working fine at close range still shoot high at distance?
Yes. Each yardage setting is separate, so a sight may be accurate at 20 yards but high at 50. Re-sight each distance you shoot.
Conclusion
Shooting high is usually a sight setting problem that you can fix with a methodical approach. Confirm the issue with a tight group, make small pin or tape adjustments, and retest at each distance. Keep your settings recorded so you can return to them whenever you need to.
Related reading
- How to Adjust a Trophy Ridge Bow Sight: Step-by-Step for Beginners
- How to Adjust Peep Sight Without Bow Press: 6 Steps for Archers
- Hind Sight Bow Sight: How to Set Up and Use One for Target Shooting
Ready to choose one?
