How to Make a Back Quiver: A Step-by-Step Guide for Beginners
Learn how to make a back quiver at home with this step-by-step guide covering materials, pattern sizing, stitching and final fitting for a comfortable carry.
Updated November 2026
Learning how to make a back quiver gives you a carry system sized exactly to your arrows, your bow and your body. With basic leather, a sharp knife and a few hand tools, you can build a simple tube-style quiver that holds arrows securely and sits comfortably between your shoulder blades. The process takes a little patience, but each step is straightforward.
Gather Materials and Measure Your Arrows
Start with the measurements, because everything else depends on them. Most home makers use a single piece of vegetable-tanned leather around 2 to 3 mm thick, which is firm enough to hold shape but still easy to stitch. Measure the longest arrow you plan to carry, then add about 2 inches for the quiver’s length, and measure the diameter of your arrow bundle where it will sit.
Shopping for one? See our guide: Bear Archery Traditional Back Quiver Review (2026).
You will also need:
- Vegetable-tanned leather, cut large enough for your pattern
- A metal ruler, pencil and utility knife or leather cutting knife
- Leather-working awl and waxed thread
- Contact cement or leather glue
- Rivets or snaps and a strap for the shoulder harness
- A wooden or plastic tube form the same diameter as your arrow bundle, for shaping
Cut and Shape the Quiver Body
Draw your pattern on the flesh side of the leather. A common layout is a rectangle that wraps around your tube form with a 1/2-inch overlap for the seam, plus a rounded bottom piece sized to the tube’s base. Cut slowly, keeping your knife vertical so the edges stay square.
Dampen the leather lightly and wrap it around the form. Hold it in place with clamps or tape and let it dry. The leather will keep this shape once fully dry, which is what gives the quiver its firm, open mouth.
Stitch the Seam and Attach the Base
Punch stitch holes about 1/8 inch from the edge and roughly 1/4 inch apart. Use a saddle stitch with waxed thread so the seam stays strong under the weight of arrows. Pull each stitch snug but not so tight that the leather puckers.
Glue the bottom piece into place, then stitch it through the same holes. Trim any loose thread and burnish the edges with a little water and a smooth tool so they look finished.
Add the Harness and Check the Fit
Attach the shoulder straps with rivets or snaps at the top corners of the quiver. Position the quiver so the mouth sits slightly above your shoulder blades and the arrow tips stay well clear of your head. Put the quiver on, draw your bow arm through the motion of reaching back, and confirm the arrows do not rattle or shift.
Quick Fitting Checklist
- Arrows slide in and out smoothly with no snagging.
- The quiver sits flat against your back without swaying.
- Straps are even and adjustable.
- Arrow fletching is protected from rubbing.
Common Mistakes to Avoid
- Cutting the tube too short. Leave room for your longest arrow plus a little clearance at the top.
- Skipping the form. Shaping the leather on a tube keeps the opening round and the arrows secure.
- Over-tightening stitches. Tight stitches pucker the leather and can tear it under load.
- Attaching straps too low. A low quiver swings and knocks your hip when you move.
- Testing only while standing still. Walk, bend and draw to be sure the quiver stays put.
If you are unsure about your measurements or your first build, our leather archery guides and a local leatherworking instructor can help you check your work. For tips on fit and carrying style, see Hill Style Back Quiver: How to Choose, Fit and Use One (Step-by-Step) and Traditional Leather Back Quiver: A Step-by-Step Guide for Beginners.
Recommended Gear
- Leather-working awl and waxed thread – these make a saddle stitch easy to repeat evenly along the seam. View on Amazon
- Leather cutting knife with replaceable blades – clean, straight cuts keep the seams aligned. View on Amazon
- Contact cement for leather – it holds the base in place while you stitch it. View on Amazon
FAQ
What leather works best for a back quiver?
Vegetable-tanned leather around 2 to 3 mm thick is the most common choice. It holds its shape when dampened and dried over a form and stitches cleanly.
How long should a back quiver be?
Measure your longest arrow and add about 2 inches. This leaves room for the arrow tips to sit below the mouth without sticking out at the top.
Do I need a form to shape the quiver?
A form is strongly recommended. Without one, the tube will likely collapse or flatten, which makes arrows harder to draw and return.
Conclusion
Once you know the measurements and build order, learning how to make a back quiver becomes a manageable weekend project. Take your time with the cutting and stitching, and always check the fit with your bow and arrows before you rely on it. A carefully made quiver will serve you well for many seasons.
Related reading
- Mounted Archery Back Quiver: How to Choose and Fit One for Horseback Shooting
- Bow and Quiver on Back: How to Carry Both Safely and Comfortably
- Youth Archery Back Quiver: A Step-by-Step Fitting and Setup Guide
Ready to choose one?
