Hill Style Back Quiver: How to Choose, Fit and Use One (Step-by-Step)
Learn what a hill style back quiver is, how to choose the right size, and how to fit and wear one so your arrows stay secure and your draw stays smooth.
Updated November 2026
A hill style back quiver is a traditional arrow carrier that rides on your back, with the arrows held upright and angled over one shoulder. This guide explains what sets the design apart, how to pick one that suits your bow and body, and how to fit and wear it so arrows stay secure and your draw arm stays clear.
What Sets a Hill Style Back Quiver Apart
The hill style design holds arrows in a tube or fabric sleeve that sits high on the back, with the nocks pointing up and toward the shoulder. Unlike a hip quiver, it keeps arrows out of the way of your bow arm and leaves your hips free. Most traditional and recurve archers use this style for field shooting, where a hip quiver can snag on brush or swing into the bow.
Shopping for one? See our guide: Bear Archery Traditional Back Quiver Review (2026).
Because the arrows sit upright, the quiver works best with a consistent arrow length and a clean grip on the shaft. Manufacturers typically specify a maximum arrow length and diameter, so check those figures before buying. For a broader comparison of carriers, see What Holds Arrows in Archery: Quivers, Arrow Rests and Holders Explained.
Choosing the Right Size and Material
Start by measuring your arrows. Count the number of arrows you need to carry for a session, then add two or three spares. Measure the shaft diameter at the widest point, not the fletching, and compare it with the quiver’s stated capacity.
- Confirm the arrow count you carry on a typical outing.
- Measure arrow shaft diameter and length.
- Check the quiver’s listed arrow length and diameter limits.
- Decide between leather, canvas or synthetic materials based on weather and how much noise you want.
- Test the fit by slipping arrows in and out one-handed.
Leather is traditional and quiet but needs oiling in wet weather. Synthetic and canvas options handle rain better and cost less care time. For leather-specific advice, read Leather Archery Back Quiver: A Step-by-Step Guide to Choosing and Setting One Up.
Fitting and Adjusting the Quiver
A well-fitted hill style quiver sits high between the shoulder blades, with the top of the tube roughly level with your shoulder. The arrows should lean slightly away from your body so the fletching clears your neck and hair.
Step-by-Step Fitting
- Put the quiver on and tighten the shoulder strap until the body rests against your upper back without sliding.
- Load a full set of arrows and check that they stay in place when you bend forward.
- Draw your bow several times. If fletching brushes your face or ear, lower the quiver or adjust the angle of the tube.
- Reach over your shoulder and pull an arrow out smoothly. Repeat with each hand position you use in the field.
- Confirm the quiver stays in place when you walk, kneel and climb. Tighten the chest strap if needed.
Fitting for a youth archer follows the same logic but with shorter straps and lighter loads. Youth Archery Back Quiver: A Step-by-Step Fitting and Setup Guide covers the adjustments in detail.
Wearing and Using It Safely
Keep the arrow points covered when you are not shooting. Use a point cap or a closed tube so arrows do not poke through clothing or injure someone nearby. Before shooting, check that no arrow is loose, since a shifting shaft can drop out during a draw.
When you walk through brush, turn your body so the quiver does not catch on branches. For horseback shooting, the design changes, so see Mounted Archery Back Quiver: How to Choose and Fit One for Horseback Shooting.
Common Mistakes
- Choosing a tube that is too short, so arrows bounce loose when you move.
- Strapping the quiver too low, which lets the nocks drop and snag.
- Ignoring fletching clearance, which causes fletch-to-face contact during draws.
- Storing leather quivers wet, which leads to mold and stiff material.
- Skipping a fit check after changing your arrows to a different length or diameter.
Recommended Gear
A spare set of quiver straps is useful if you change clothing layers or shoot in different seasons, since fit shifts with a heavier jacket. View on Amazon
A leather care kit helps keep traditional quivers supple and water-resistant between outings. View on Amazon
A quiver liner or insert keeps arrows from rattling and protects fletching in a tube-style carrier. View on Amazon
FAQ
How many arrows should a hill style back quiver hold?
Most models hold between six and twelve arrows, depending on shaft diameter. Check the manufacturer’s stated capacity, and allow room for spares so you are not reloading mid-round.
Can I use a hill style quiver for hunting?
Many archers do, since the upright carry keeps arrows clear of the bow arm. Confirm the quiver is secure enough for your terrain, and check local regulations on equipment for your hunt.
How do I stop my arrows from rattling in the quiver?
Tighten the tube’s retaining strap or add a foam liner. Rattling usually means the arrows have too much room, so a snug fit solves most cases.
Conclusion
A hill style back quiver works well when the arrow count, shaft size and strap fit all match your setup. Measure your arrows, fit the quiver to your shoulders and test your draw before heading out. Re-check the fit whenever you change arrows or clothing, and consult a qualified archery coach if you are unsure about setup.
Related reading
Ready to choose one?
