We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

Making a Back Quiver: A Step-by-Step Guide for Beginners

Learn making a back quiver step by step, from choosing materials and cutting the pattern to sewing, fitting and finishing a quiver that carries arrows securely.

Updated November 2026

Making a back quiver is a practical project that a patient beginner can finish in a weekend. You will choose suitable materials, cut and shape the body, add a secure arrow retention system, and fit the strap so the quiver rides comfortably between your shoulder blades. The result should hold your arrows snugly, stay quiet while you walk the line, and draw without snagging your bowstring.

Plan the Size and Materials

Start by measuring your arrows. Count the arrows you plan to carry, usually four to six for target shooting, and measure the widest point of the fletchings. Add about 1 inch of clearance so the feathers or vanes can slide in and out without crushing. Most back quivers are built with a tube or pocket roughly 4 to 6 inches deep, but your arrow length and quiver height should be checked against your own draw.

Shopping for one? See our guide: Bear Archery Traditional Back Quiver Review (2026).

For materials, veg-tanned leather around 2 to 3 ounces is a common choice for the body, with a thinner lining if you want a softer feel against your back. You will also need a strap material such as 1-inch leather, webbing or nylon belting, plus thread, rivets or snaps, and a backing board or stiff insert if you want the mouth of the quiver to stay open.

Cut, Shape and Join the Body

  1. Draw a flat pattern on paper. Include the front panel, back panel, bottom and two side gussets if you want a boxed shape.
  2. Transfer the pattern to leather and cut with a sharp knife or rotary cutter. Mark stitch lines about 1/8 inch from the edge.
  3. Punch stitch holes with a diamond chisel or stitching pony at an even spacing, roughly 6 to 8 stitches per inch.
  4. Dampen the leather slightly and fold or form it around a wooden form or a rolled-up arrow shaft so the tube keeps a round mouth.
  5. Sew the seams with a saddle stitch, then trim any uneven edges and burnish them.

If you want to learn the basics of cutting and forming before committing a whole quiver, a simple pouch or leather arm guard makes a good practice piece. For a complete beginner build, the approach in Traditional Leather Back Quiver: A Step-by-Step Guide for Beginners walks through each stage in more detail.

Add Arrow Retention and the Strap System

A back quiver needs a way to keep arrows from sliding out when you bend or run. Many makers add a rear retention strap or a fold-over flap that buckles over the arrow nocks. Another option is an inside liner that grips the shafts gently. Test the retention with your arrows before you finalize it: the arrows should stay put when you shake the quiver, yet slide out with one smooth pull.

For the carry strap, attach a loop or sleeve on each top corner. Sew a shoulder strap that crosses the chest and a waist or hip strap if you want the quiver to stay steady while you move. Adjust the length so the quiver sits high enough that the arrow tips clear your hip and low enough that the bowstring does not catch on the top of the quiver when you reach over your shoulder. The fitting advice in Youth Archery Back Quiver: A Step-by-Step Fitting and Setup Guide is useful if you are building for a smaller archer.

Finish, Fit and Test

Finish the leather with a light coat of conditioner or a sealant, then let it dry fully before the first use. Check every stitch line, rivet and snap for looseness. Put the quiver on, load it with arrows and draw a few times to confirm that the bow limbs and the string clear the top of the quiver. Walk, kneel and reach to make sure nothing shifts or creaks. If the quiver tilts forward, shorten the chest strap or move the attachment points a little higher.

Common mistakes to avoid

  • Making the tube too tight, which scrapes fletchings and slows the draw.
  • Skipping a stiff insert, so the mouth collapses and arrows are hard to grab.
  • Placing the strap anchors too low, which lets the quiver swing into your draw side.
  • Using thread that is too thin for the load, which can pull through the leather over time.
  • Testing only while standing still instead of moving through a real shooting motion.

A good set of leather-working tools makes the stitching far more consistent. A stitching chisel set and a stitching pony help keep holes evenly spaced, while a leather burnisher gives the edges a clean finish. View on Amazon

Waxed linen thread holds up well in saddle stitching and resists fraying under tension. View on Amazon

A sharp leather knife or rotary cutter produces clean edges that make the sewing and burnishing easier. View on Amazon

FAQ

How much leather do I need for a back quiver?

A single back quiver usually needs one piece for the body, one for the lining if you use it, and enough for the straps. Measure your pattern first and add a margin of several inches on each side to allow for trimming and mistakes.

Do I need special tools to make a back quiver?

You can start with a sharp knife, a ruler, an awl, a stitching chisel and waxed thread. Power tools are optional and not required for a basic build.

How long does it take to make a back quiver?

Many beginners finish a simple quiver over a weekend, allowing time for leather to dry and finish between steps. Fancier designs with lining, pockets or decorative tooling take longer.

Conclusion

Making a back quiver comes down to accurate measurements, careful stitching and a retention and strap system that suits how you shoot. Test the fit with your real arrows and your full draw before you rely on it in the field. A well-built quiver should last for many seasons with simple care, and each one you make will teach you something useful for the next.

Lauren Holland

About Lauren Holland

Lauren Holland is part of our editorial team and reviews and edits our target archery guides, checking product details against manufacturer specifications and owner feedback.

About the author

Lauren Holland
Lauren Holland

Lauren Holland writes reviews and buying guides for Archery Society.