We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

3 Axis Bow Sight: How to Set Up and Sight In for Beginners

Learn what a 3 axis bow sight does, how to set up its three adjustments and sight in your first pins for accurate shooting. A clear beginner walkthrough.

Updated November 2026

A 3 axis bow sight lets you adjust a pin on three planes: up and down, left and right, and rotation. Once you understand what each adjustment does, you can get a 3 axis bow sight level, aligned with your bow and sighted in for a specific distance in under an hour. This guide walks through the adjustments in the order that keeps your work simple.

What the Three Axes Do

Most 3 axis bow sights mount to the riser with a bracket that carries a sight housing and one or more pins. The three adjustments handle different problems:

Shopping for one? See our guide: Bow Sights with Rangefinder: 5 Best Picks Compared (2026).

  • Vertical (height): moves the pin up or down to set elevation for a given distance.
  • Horizontal (windage): moves the pin left or right to correct for the arrow drifting off target.
  • Rotation (cant): tilts the sight so the pin housing sits level with the ground, which keeps your vertical and horizontal movements from fighting each other.

Rotation comes first. If the sight is canted, every change you make to height or windage will shift the point of impact in a way that is hard to predict.

Step-by-Step Setup

Step 1: Mount and Level the Sight

Attach the sight bracket to the riser following the mounting instructions for your model. Hang a plumb line or use a bubble level on the bow’s string. Rotate the sight housing until the vertical pin sits parallel to the plumb line. Tighten the lock screws only after you are satisfied with the alignment.

Step 2: Set the Horizontal Position

Set the windage so the pin is roughly centered over the arrow path when you draw to your anchor. Shoot a few arrows at a close target, around 10 yards, and adjust left or right until your groups are centered on the bullseye.

Step 3: Sight In the Vertical Pin

Choose your first distance, such as 20 yards. Shoot groups of three to five arrows, letting each one land before adjusting. Move the vertical pin up if you are hitting low and down if you are hitting high. Make small changes, then shoot again.

Step 4: Add Additional Distances

Once your first pin is grouping well, move back to the next distance and repeat the process. Mark each pin with its yardage once it is set. Check the manufacturer’s sight manual for the recommended adjustment method for your model.

Quick Setup Checklist

  1. Confirm the bow is tuned and the arrow is nock-centered before sighting in.
  2. Mount the sight and level the housing with a plumb line.
  3. Set windage at 10 yards until groups are centered.
  4. Sight in the first pin at your chosen distance.
  5. Repeat for each additional pin, labeling as you go.
  6. Re-check after any change to your draw length, arrow or bow.

Common Mistakes

  • Adjusting height before leveling the sight, which makes every later change less predictable.
  • Sighting in while tired or rushing, which hides problems with form and produces bad adjustments.
  • Tightening lock screws too hard, which can strip threads or shift the setting.
  • Forgetting to recheck after swapping arrows or changing draw weight.
  • Using a sight that does not match your bow’s riser mounting pattern.
  • A bow level or plumb line kit: makes leveling the sight quick and repeatable. View on Amazon
  • Target face with a clear center: helps you read group placement at close range during windage setup. View on Amazon
  • A sight manual or pin tape: keeps yardage labels and settings written down so you can repeat them later. View on Amazon

FAQ

Is a 3 axis bow sight harder to set up than a single pin sight?

It takes more steps because you have three adjustments, but the process is straightforward once you level the housing first. Many shooters find the extra adjustment useful for fine tuning.

Why does my 3 axis sight keep moving?

Loose lock screws or a bracket that is not fully seated are the usual causes. Check each fastener and confirm the mount is secure before shooting.

How often should I re-sight my 3 axis bow sight?

Re-check whenever you change arrows, draw length, string or bow weight, and periodically if your groups drift. For specific guidance on your model, consult the manufacturer’s manual or a qualified archery pro shop.

Conclusion

A 3 axis bow sight rewards a methodical approach: level the housing, set windage, then sight in each pin at its distance. Take your time, label your pins, and re-check after any change to your setup. Good groups follow from consistent form and small, careful adjustments.

Ethan Brooks

About Ethan Brooks

Ethan Brooks is part of our editorial team and reviews and edits our target archery guides, checking product details against manufacturer specifications and owner feedback.

About the author

Ethan Brooks
Ethan Brooks

Ethan Brooks writes reviews and buying guides for Archery Society.