Truglo Bow Sight Replacement Parts: What to Buy and How to Swap Them
Find the right truglo bow sight replacement parts, learn which pieces wear out, and follow simple steps to swap them safely at the range.
Updated November 2026
Truglo bow sight replacement parts are usually simple to identify and swap once you know which component has failed. Most problems come from worn pins, bent or loose brackets, or a scratched lens, and each can be fixed without replacing the whole sight. This guide explains how to diagnose the problem, match the correct part, and install it so your sight holds its settings.
Identify the Part You Actually Need
Before ordering anything, take a close look at the sight and note which component is damaged. Pins and fiber optic fibers are the parts that wear out most often, and the mounting bracket can loosen or bend after a hard fall. Many archers also replace the light-gathering fiber or the sight housing when the pin guard gets chipped.
Shopping for one? See our guide: Bow Sights with Rangefinder: 5 Best Picks Compared (2026).
Check the sight model number, usually stamped on the bracket or printed on the packaging. Parts are often model specific, so a pin set made for one Truglo series may not fit another. Manufacturers specify compatible models in their product listings, so confirm the fit before you order.
Match the Part to Your Setup
Once you know the model, compare the part dimensions with the original. Pin diameter, pin length and bracket hole spacing all matter. If you use a single-pin or multi-pin sight, make sure the replacement set uses the same pin count. Mixing pin sizes can cause the sight to shift under load.
If you are also replacing the arrow rest or other accessories at the same time, plan the install order so you do not disturb the sight twice. For arrow rest compatibility and setup, see Ripcord Arrow Rest Replacement Parts: What to Buy and How to Swap Them, which covers how rest parts interact with the bow.
Swap the Part Step by Step
Work on a clean, flat surface and keep the small hardware in a labeled tray. Remove the bow string or unload the limbs if your bow design requires it, and follow the manufacturer’s torque guidance for any mounting screws.
- Remove the sight from the riser and set the hardware aside in order.
- Take the old pin or fiber out and compare it to the new part before fitting.
- Seat the new pin or fiber fully, without forcing it past the housing stop.
- Reattach the bracket and snug the screws evenly, checking for play.
- Recheck the sight on the bow and confirm that all pins move freely.
Set and Test the Sight
After the swap, reset your pin gap and sight at known distances, starting close and working outward. Shoot a few groups at 10 yards to confirm the new part holds its position. If the grouping drifts, loosen the bracket slightly and re-level the sight, then tighten again.
| Problem | Likely part | Action |
|---|---|---|
| Pin will not hold setting | Pin set | Replace pins |
| Dim or faded aiming dot | Fiber optic | Replace fiber |
| Sight shifts on the riser | Bracket or screws | Tighten or replace bracket |
| Scratched housing | Sight housing | Replace housing |
Common Mistakes
- Ordering parts without checking the exact sight model number.
- Overtightening small screws, which can strip threads or crack the bracket.
- Forcing a pin into the housing instead of confirming the fit first.
- Skipping the test shots, which hides a loose or misaligned new part.
- Ignoring a bent bracket after a fall, which affects accuracy long before it looks damaged.
Recommended gear
- Small hex and Torx driver set: Bow sight screws are small, and a fitted driver set prevents stripped heads. View on Amazon
- Blue threadlocker: A light threadlocker helps keep bracket screws from backing out under vibration. View on Amazon
- Archery bow stand: A stable stand keeps the bow still while you work on the sight. View on Amazon
FAQ
Can I replace only one pin in a Truglo sight?
Often yes, if the pin is available separately and matches the sight model. Replacing a single pin can change its feel or alignment, so re-sight the whole set afterward.
How do I know if the sight housing needs replacing?
Replace the housing if it is cracked, bent, or no longer holds the pins or bracket securely. Minor scratches usually do not affect function.
Should I consult a professional for sight repairs?
For a simple pin or fiber swap, most archers can manage at home. If the bracket is bent or the bow shows damage, consult a qualified bow technician before shooting.
Conclusion
Most truglo bow sight replacement parts can be swapped in under an hour once you identify the faulty component and confirm the model. Take your time with the fit, tighten screws evenly, and test with short groups before you shoot at longer distances. Keep spare parts on hand if you shoot often, since pins and fibers are the most common wear items.
Related reading
- Garmin Rangefinder Bow Sight: Setup, Calibration and Use Guide
- Why Do Archery Attack Bows and Arrows Miss? 6 Causes and Fixes
- Traditional Bow Arrow Rest: 7 Best Picks Compared for 2026
- Top 7 Archery Bow Arrow Rest Options Compared for Recurve and Compound Bows
Ready to choose one?
