We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

Tetra Max Bow Sight: Setup, Sight Pin Tuning and Tips for Beginners

Learn how to mount, level and sight in a tetra max bow sight, with pin tuning steps, common mistakes to avoid and tips for accurate shooting.

Updated November 2026

A tetra max bow sight is a multi-pin archery sight designed to give you a repeatable aim point at several distances. This guide walks you through mounting the sight, leveling it, setting the pins for your bow and checking your groups so your first session on the range is productive. Specific fit and adjustment details can vary by model, so always check the instructions packed with your sight.

What You Need Before You Start

Gather your tools and a safe shooting setup before you touch the bow. Work on a stable bench or in a stand, and keep the bow unstrung unless the manufacturer’s instructions say otherwise.

Shopping for one? See our guide: Bow Sights with Rangefinder: 5 Best Picks Compared (2026).

  • The sight, its mounting bracket and included hardware
  • Allen (hex) keys in the sizes listed in your sight’s manual
  • A small bubble level or the level built into the sight
  • A tape measure and a target with a clear aiming mark
  • Arrows already tuned for your bow, plus a fletching-free test arrow if you have one

Step 1: Mount the Sight and Set the Bracket

Attach the bracket to the riser using the mounting holes on your bow. Snug the bolts so the bracket holds firm, but do not overtighten, since you will need to make small adjustments later. Position the sight so your eye can line up the pins with the target through the peep sight without strain.

Step 2: Level the Sight

A level sight keeps your pins tracking true from one distance to another. Set the level so the pin array is vertical relative to the ground when the bow is held at full draw. Recheck the level after every adjustment, because a sight that looks straight on the bench can tilt once the bow is drawn.

Step 3: Set Your Pins

Start with the closest pin and shoot from a known distance, such as 20 yards. Adjust that pin until your arrows group where you want them. Then move to the next pin distance and repeat the process. Shoot a set of three to five arrows before making each adjustment, since one or two shots rarely show a true pattern.

  1. Shoot a group of three to five arrows at your first distance.
  2. Note where the group lands compared with your aim point.
  3. Move the pin up or down, or move the sight slightly, to correct the group.
  4. Repeat until the group centers on the aim point.
  5. Move to the next distance and repeat.

Checking Your Setup and Troubleshooting Groups

Consistent results depend on steady form as much as on sight settings. If your groups scatter, check your anchor point, release and bow grip before you blame the sight. Many misses that look like sight problems are really form problems. For more on why arrows miss, see Why Do Archery Attack Bows and Arrows Miss? 6 Causes and Fixes.

Symptom Likely cause What to check
Groups high or low Pin set at wrong height Adjust the vertical pin position for that distance
Groups left or right Sight not centered or bracket loose Re-center the sight and tighten the bracket
Pins drift when drawn Sight not level Re-level and recheck at full draw

Common Mistakes

  • Setting pins from a single arrow instead of a group of several shots.
  • Skipping the level check after changing the bracket position.
  • Tightening the mounting bolts so hard that small adjustments become difficult.
  • Changing arrows, draw length or release without rechecking the pins.
  • Shooting at distances you have not marked, then assuming the pins are wrong.

A bubble level that attaches to the bow or sight makes leveling faster and more repeatable than eyeballing it. Try searching for View on Amazon to compare options.

A soft target with a visible aiming mark helps you read group placement at each distance. Search for View on Amazon to find a suitable option.

FAQ

Do I need a bow press to mount a tetra max bow sight?

A bow press is not required for most mounting steps, but it can make working on a strung bow safer. Follow the manufacturer’s instructions for your bow and sight.

How often should I recheck my pin settings?

Recheck after any change in arrows, draw length, release, string or sight position, and periodically if your form changes. Groups that drift over time usually point to a form change or a loose component.

Can I use a tetra max bow sight on a recurve bow?

Sights designed for compound bows generally do not fit recurve bows, which use a different mounting setup. Check compatibility with the manufacturer before buying or mounting any sight.

Conclusion

With the sight mounted, leveled and pinned in steps, you will have a repeatable aim point at each distance you practice. Take your time, shoot groups rather than single arrows, and check your form whenever results shift. Refer to your sight’s manual for model-specific details.

Ethan Brooks

About Ethan Brooks

Ethan Brooks is part of our editorial team and reviews and edits our target archery guides, checking product details against manufacturer specifications and owner feedback.

About the author

Ethan Brooks
Ethan Brooks

Ethan Brooks writes reviews and buying guides for Archery Society.