We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

Dead Nuts Bow Sight: How to Set One Up for Accurate Shots

Learn what a dead nuts bow sight is, how to set one up for accurate shots at every distance, and the common mistakes that cause misses.

Updated November 2026

A dead nuts bow sight is a sight setting in which the pin sits exactly on the target at the distance you are shooting, with no holdover or hold-under needed. Getting there means tuning your bow, anchor and sight so that each pin lines up with a known yardage. This guide walks through the process for a new archer working with a standard compound or recurve sight.

What “Dead Nuts” Means for Your Sight

In practice, dead nuts means your aim point and your arrow’s impact point match for a given distance. If your 20-yard pin lands dead center at 20 yards, you have a dead nuts setting for that pin. Most archers aim for one or two dead nuts pins, then use holdover for the rest, because tuning every pin perfectly takes time and consistency.

Shopping for one? See our guide: Bow Sights with Rangefinder: 5 Best Picks Compared (2026).

Before you touch the sight, confirm that your bow is tuned. A sight can only be as accurate as the arrow flight underneath it. If your arrows are porpoising or fishtailing, see Why Do Archery Attack Bows and Arrows Miss? 6 Causes and Fixes before continuing.

Step-by-Step: Setting Your Dead Nuts Pin

  1. Set your bow to its draw length and confirm your anchor point is the same on every shot.
  2. Shoot a group of at least six arrows at 20 yards from a stable stance.
  3. Measure the group’s center relative to the bullseye. Note whether arrows are high, low, left or right.
  4. Adjust the pin on the sight housing so the group center moves to the aiming point. Make small changes, about a quarter turn of the adjustment at a time.
  5. Repeat the group until your arrows land within a few inches of the aim point.
  6. Mark the setting, then move back and repeat the process at 30 and 40 yards to build your pin ladder.

Checking Your Anchor and Release

A dead nuts setting only holds if your anchor is consistent. Inconsistent anchor position moves your impact point by several inches, which looks like a sight problem but is really a form problem. Use a kisser button or the same string landmark every time, and keep your release hand relaxed.

Verifying and Maintaining the Setting

Recheck your dead nuts pin whenever you change arrows, string, or cams, or after a long break. Temperature and humidity can also shift arrow spine slightly. Check the pin at the start of each season, then again after any major equipment change.

Check When to Do It What to Look For
Group center at 20 yards Start of each session Within 2 inches of aim point
Anchor consistency Every shooting session Same string landmark each shot
Pin housing tightness Monthly No movement when you tap the sight
Arrow tune After any arrow or string change Clean paper tear

Common Mistakes

  • Adjusting the sight before the bow is tuned, which leads to chasing a problem that is not in the sight.
  • Shooting too few arrows to read a group accurately. Six is a practical minimum.
  • Changing anchor or grip between shots without noticing.
  • Making large pin adjustments in one go instead of small, measured turns.
  • Skipping the recheck after a string or cam change.
  • Paper tuning kit: A paper tuning setup helps you see arrow flight and confirm your tune before you set the sight. View on Amazon
  • Bow sight level: A small bubble level mounted on the sight helps keep the bow vertical so your pin ladder stays consistent. View on Amazon
  • Stable target stand: A stable stand or backstop lets you shoot repeatable groups without fighting the target. View on Amazon

FAQ

How many dead nuts pins should I set?

Most archers set one or two dead nuts pins, usually at the distance they shoot most often. The rest of the pins can be used with holdover once you know how far off they land.

Does a dead nuts setting change with a new bow?

Yes. Any new bow, string, cam or arrow setup requires a fresh sight check, since small differences in draw force and arrow speed shift the impact point.

How often should I recheck my sight setting?

Recheck at the start of each season and after any equipment change. If your groups drift without a clear reason, check your anchor first. For persistent problems or injury concerns, consult a qualified archery coach or pro shop.

Conclusion

A dead nuts bow sight comes down to a tuned bow, a consistent anchor and careful, small pin adjustments measured against a known distance. Once you have one or two dead nuts pins, the rest of your pin ladder becomes much easier to use. Recheck the setting regularly, and your groups will stay tight.

Ethan Brooks

About Ethan Brooks

Ethan Brooks is part of our editorial team and reviews and edits our target archery guides, checking product details against manufacturer specifications and owner feedback.

About the author

Ethan Brooks
Ethan Brooks

Ethan Brooks writes reviews and buying guides for Archery Society.