Bow Peep Sight String: How to Install and Set Yours (Step by Step)
Learn how a bow peep sight string works, how to tie it in, and where to place it for a clean, repeatable anchor. A simple step-by-step guide for new archers.
Updated November 2026
A bow peep sight string is a small ring or circle tied into your bowstring that gives your eye a fixed reference point to look through. Once it is installed at the right height and anchored consistently, you get a sight picture that lines up the same way every shot. This guide walks through what the peep does, how to tie and place it, and how to check your setup.
What a Peep Sight Does
A peep sight is a small hole or ring placed in the string, usually between your nocking point and your drawing hand. When you draw to anchor, you look through the peep and line it up with the front sight or sight pin. The ring centers your eye and removes the guesswork of where your head sits. Most archers use a peep in compound and some recurve setups, and the common goal is the same: consistent alignment from shot to shot.
Shopping for one? See our guide: Bow Sights with Rangefinder: 5 Best Picks Compared (2026).
Step-by-Step Installation
Before you start, confirm your bowstring is in good condition. Check for fraying, loose strands, or worn serving at the attachment points. If the string is worn, replace it first, since a peep will not hold steady on a damaged string.
- Choose a peep that matches your string diameter. Most peeps are sized for a specific strand count, so check the packaging.
- Measure your draw length and anchor point. Draw the bow to full draw and find a comfortable anchor, where your string hand touches the same spot on your face every time.
- Mark the string at the position where the peep will sit. Many archers place it about two or three strands above the nocking point, but your own anchor and eye height decide the exact spot.
- Unserve the section of string at your mark, and insert the peep so its ring faces you when the bow is held upright.
- Tie the peep in using a bowstring knot, such as a serving tie or a half-hitch series, so it cannot slide under tension.
- Reserve the string section you opened, so the peep is secured and protected from wear.
- Draw the bow and check that the peep lines up cleanly with your eye and sight.
Setting the Peep Height and Alignment
Peep height controls how your eye lines up with the sight. A peep that sits too high or too low forces you to change your head position, which makes groups drift. To set it, anchor normally, close one eye, and look through the peep. If you can see the full sight housing or pin clearly with the peep centered in your view, the height is close. Small changes of a few millimeters can make a noticeable difference, so adjust in small steps and shoot a test group after each change.
Checking Peep Alignment
Alignment is about the peep sitting square to the string. Rotate the peep slightly and see whether the ring tilts. A tilted ring can cause you to cant your head, which affects vertical and horizontal groupings. Keep the peep flat and centered in your sight line.
Common Mistakes
- Installing a peep on a worn or stretched string, which lets it slip under load.
- Setting peep height before you have a stable anchor point.
- Using a peep that does not match your string diameter, causing it to wobble or rotate.
- Making large height changes instead of small adjustments you can test.
- Skipping the check of peep alignment after a string change or bow tune.
Recommended Gear
A quality bowstring peep kit keeps the ring securely fixed and makes height changes easier to test. View on Amazon
A bow string serving thread gives you a neat, durable wrap around the peep and the string. View on Amazon
FAQ
Can I install a peep sight without a bow press?
Yes, many archers tie a peep in by hand, but you must keep the string at full brace and check the tie before shooting. If you are unsure, have a qualified bow technician install it.
How often should I check the peep’s position?
Check it whenever you change strings, adjust your anchor, or notice grouping drift. A quick look at alignment before each session catches most problems.
Will a peep sight help with accuracy?
A peep gives a repeatable eye reference, which many archers find improves consistency. It does not fix form problems on its own, so pair it with steady anchor and release practice.
Conclusion
A properly tied and aligned bow peep sight string gives you a consistent reference every time you draw. Install it on a sound string, set the height in small steps, and recheck alignment after any change. With those basics in place, the peep becomes a reliable part of your shooting routine.
Related reading
- Bow Sight Without Peep: Setup Steps for Accurate Shots (2026)
- Trophy Ridge Bow Sight Battery Size: Which Battery to Use (2026)
- Hind Sight Bow Sight: How to Set Up and Use One for Target Shooting
Ready to choose one?
