Single Pin Bow Sight Tape: How to Set Up and Use One Correctly
Learn how a single pin bow sight tape works, how to set it up and mark distances accurately, plus common mistakes to avoid on the range.
Updated November 2026
A single pin bow sight tape is a marked guide that helps you set one sight pin to the correct position for each distance you shoot. Once you learn how to measure your arrow’s trajectory, mark your tape, and fine-tune it at the range, you can shoot accurately at several yards with only one pin in view. This guide walks through the process step by step.
What a Single Pin Bow Sight Tape Does
A single pin sight uses one fixed pin that you move up or down the sight tape to match the distance to your target. Each distance mark on the tape corresponds to a point where the pin should sit so your arrow lands where you aim. Because the pin moves rather than the bow’s sight picture changing, the tape is the reference that keeps your settings consistent from session to session.
Shopping for one? See our guide: Bow Sights with Rangefinder: 5 Best Picks Compared (2026).
Most archers begin with a tape marked in yard increments, though some use metric marks. The key is that every mark is based on your own bow, arrow, draw length and shooting form, not on a generic chart.
Step-by-Step Setup
- Mount the sight securely and confirm it is level with the bow. A tilted sight shifts every reading.
- Set the single pin in the upper part of the tape and check that it moves smoothly without binding.
- Shoot from a fixed, measured distance such as 20 yards, using your normal anchor and release.
- Note where the arrow hits relative to the center. If it lands high, lower the pin; if low, raise it.
- Repeat at 30, 40 and 50 yards, shooting several arrows at each distance and using the group’s center as your reference.
- Mark each distance on the tape once the group consistently lands where you aim.
- Verify your marks at longer distances during later sessions, since small form changes can shift them.
Measuring and Marking Distances Accurately
Accuracy depends on measuring distances carefully. Use a tape measure or a laser rangefinder, and mark your shooting lane at each point before you begin. Stand at the same spot every time, and keep your anchor point consistent. Shooting groups of three to five arrows at each distance gives you a more reliable center than judging from a single shot.
| Distance | What to check |
|---|---|
| 20 yards | Group center sits where you aim; pin mark set |
| 30 yards | Pin moved only as needed; group remains tight |
| 40 yards | Consistent release and anchor; no drift in group |
| 50 yards | Re-check after a warm-up; confirm mark |
Fine-Tuning Your Tape Over Time
Your tape is not permanent. Changes in draw weight, string wear, arrow weight or even temperature can shift your impact points. Recheck your marks at the start of each season and whenever you change equipment. If you are new to adjusting sights, the general approach in Compound Bow Arrow Rest Adjustment: A Step-by-Step Guide for Beginners offers useful habits that carry over to sight tuning, such as making one change at a time and recording results.
If your groups scatter rather than shift, the problem is probably form rather than the tape. Work on a consistent anchor and release before adjusting marks again. Guides on general accuracy problems, such as Why Do Archery Attack Bows and Arrows Miss? 6 Causes and Fixes, can help you narrow down the cause.
Common Mistakes
- Marking distances from a single arrow instead of a group.
- Shooting from an inconsistent anchor, which moves every mark.
- Skipping rechecks after changing arrows, string or draw weight.
- Using a sight that is not level, which skews all readings.
- Assuming a tape copied from another archer will fit your bow.
Recommended Gear
A quality laser rangefinder makes it far easier to mark exact distances on your lane, and many archers use one alongside their tape. View on Amazon
A sturdy range target with clear grid lines helps you judge group centers at each distance. View on Amazon
FAQ
How many arrows should I shoot to mark one distance?
Shoot three to five arrows at each distance and use the center of the group as your reference. A single arrow can mislead you because of small release variations.
How often should I recheck my single pin tape?
Recheck at the start of each season and after any change to your bow, string, arrows or draw weight. Quick checks at 20 and 30 yards are often enough between full sessions.
Can I use someone else’s tape on my bow?
It is not recommended. Your draw length, bow setup and form all affect the marks, so each archer needs to set their own tape.
Conclusion
A single pin bow sight tape works best when you measure distances carefully, shoot groups rather than single arrows, and recheck your marks regularly. Take your time during setup and make one change at a time. With consistent form, your marks will become a reliable reference for every shooting session.
Related reading
- Garmin Rangefinder Bow Sight: Setup, Calibration and Use Guide
- Traditional Bow Arrow Rest: 7 Best Picks Compared for 2026
Ready to choose one?
