We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

Bow Sight Mounting Screws: How to Install and Tighten Them Correctly

Learn how bow sight mounting screws should be installed, torqued and checked so your sight stays aligned. Step-by-step guide for compound and recurve archers.

Updated November 2026

Bow sight mounting screws hold your sight steady on the riser, and a sight that shifts even slightly will throw your groupings off target. In this guide you will learn how to identify the right screws, seat them without cross-threading, tighten them to a firm and even hold, and check that the sight stays put after a session of shooting.

Identify the Right Screws Before You Start

Most bow sights attach to the riser through a bracket or mounting plate, and the screws that hold that plate are usually metric machine screws. Manufacturers typically specify the thread size and length in the sight’s instructions, and many include a small set of replacement screws. Check that the screw length is correct for your riser: a screw that bottoms out before it clamps the bracket will look tight but may not hold, while one that is too long can damage the riser or stop the bracket from seating flat.

Shopping for one? See our guide: Bow Sights with Rangefinder: 5 Best Picks Compared (2026).

Before you install anything, look at the threaded holes on the riser for debris, old thread locker, or paint. Clean them with a dry cotton swab. Do not force a screw into a hole that feels gritty or resists the first turns.

Step-by-Step Installation

  1. Lay the sight bracket against the riser in its intended position and hold it there while you start the screws by hand.
  2. Thread each screw by hand for at least two full turns before using any tool. If it does not turn smoothly, back it out and check alignment.
  3. Snug the screws in a crisscross pattern, alternating between them, so the bracket pulls down evenly.
  4. Tighten to the torque value in the manufacturer’s instructions. If no value is listed, use a hex key with a torque driver and stop when the bracket is firm and the screws do not move under gentle pressure. Avoid pushing a short hex key with your full body weight, which can strip the head or stretch the threads.
  5. Confirm the sight is seated flat against the riser with no gap or rocking.

Check Alignment and Secure the Hold

Once the screws are tight, verify that the sight is level and square to the arrow path. Adjust windage and elevation only after the mounting hardware is fully secured, because retightening can shift your settings. If the sight drifts after a few sessions, the screws probably were not torqued evenly or the bracket was not fully seated.

Many archers use a small amount of blue (medium-strength) thread locker on the screw threads to resist loosening from vibration. Use it sparingly, and check the sight’s manual first to confirm that the product is compatible with the riser finish.

Tools You Will Need

  • The correct hex key or Allen wrench for your screw head
  • A torque driver or torque wrench, if the manufacturer lists a value
  • A dry cotton swab and a clean cloth for the threaded holes
  • Blue thread locker, optional and used sparingly

Common Mistakes

  • Cross-threading a screw by starting it at an angle or forcing it with a tool.
  • Tightening one screw fully before the others, which pulls the bracket crooked.
  • Overtightening, which can strip threads in aluminum risers.
  • Using screws of the wrong length, which can either fail to clamp or damage the riser.
  • Skipping a recheck after the first few shooting sessions, when settling is most likely.
  • Torque driver set: Lets you apply an even, measured tightness to each screw rather than guessing by feel. View on Amazon
  • Hex key set: Provides the correct head size for mounting screws, which reduces the risk of stripping. View on Amazon

For related setup steps, see Garmin Rangefinder Bow Sight: Setup, Calibration and Use Guide and Compound Bow Arrow Rest Adjustment: A Step-by-Step Guide for Beginners. If your sight has a rangefinder or electronic component, check the manufacturer’s wiring and battery guidance as well.

FAQ

How tight should bow sight mounting screws be?

Tighten them to the torque value in the manufacturer’s instructions when one is given. If no value is listed, tighten until the bracket is firm and the screws do not move under gentle pressure, then stop.

Can I use thread locker on bow sight mounting screws?

A small amount of medium-strength blue thread locker can help prevent loosening. Check the sight’s instructions and your riser’s finish first, and use it sparingly.

Why does my bow sight keep loosening?

Loosening is usually caused by uneven tightening, screws that were not fully seated, or vibration over time. Recheck the screws after the first few sessions and retighten them in a crisscross pattern.

Conclusion

Properly installed bow sight mounting screws keep your sight aligned so your adjustments hold from one session to the next. Start the screws by hand, tighten them evenly, and recheck after your first few sessions. If you are unsure about the torque value or the screw length for your specific sight, consult the manufacturer or a qualified archery pro shop.

Ethan Brooks

About Ethan Brooks

Ethan Brooks is part of our editorial team and reviews and edits our target archery guides, checking product details against manufacturer specifications and owner feedback.

About the author

Ethan Brooks
Ethan Brooks

Ethan Brooks writes reviews and buying guides for Archery Society.