Bow Peep Sight Tube: How to Install and Align One (Step by Step)
Learn what a bow peep sight tube does, how to pick the right size, and how to install and align one on your bow string for a clean, repeatable anchor.
Updated November 2026
A bow peep sight tube is a short, hollow insert set into your bowstring that lines up with your eye and sight pin, giving you a consistent anchor point every shot. This guide explains what the tube does, how to choose the right size, and how to install and align it so your sight picture stays the same from shot to shot.
What a Bow Peep Sight Tube Does
A peep sight is a small ring or sleeve tied into the string. Looking through the tube, you see a circle that frames the target and the sight pin. Because the peep sits at a fixed position relative to your eye, you can draw to the same anchor each time. Without a peep, anchor point depends on feel alone, and small changes in your draw length or cheek weld can move the arrow noticeably at distance.
Shopping for one? See our guide: Bow Sights with Rangefinder: 5 Best Picks Compared (2026).
Choosing the Right Tube Size
Tubes are sold by inside diameter, usually in fractions of an inch or millimeters. The right size depends on how precisely you want to see the pin:
- Narrow tubes give a tighter sight picture and can improve precision, but they demand a steady eye and good lighting.
- Wider tubes are easier to find quickly, which helps beginners and shooters in low light.
- Tube length matters too. Longer tubes can sit farther from your eye, changing how much of the target you see.
Check the manufacturer’s listing for the inside diameter and match it to your sight pin size and your eye’s preference.
Installing and Aligning the Peep
Tools and Materials
- Bow square or string level
- Serving material or peep tying thread (a serving tool helps)
- Bow press, if you have one, to hold tension safely
- Tape or a marker to mark your string position
- The bow peep sight tube itself
Installation Steps
- Unstring the bow only if your manufacturer requires it. Many shooters install peeps with the bow strung in a press.
- Mark the string with a small piece of tape at your planned peep height. A common starting point is near your normal anchor, roughly at the corner of your mouth or just under your cheek bone.
- Tie the peep into the string by serving the area above and below it. Use even, tight wraps so the peep cannot slide.
- Slide the tube into the peep hole and confirm it sits square to the string.
- Check that the peep is level with the string. A tilted peep makes the sight picture look skewed.
Alignment Check
Once the peep is installed, draw to your normal anchor and look through the tube. The sight pin should sit centered in the ring. If it does not, adjust your anchor slightly or re-tie the peep at a new height. Shoot a few arrows at a short distance to confirm groups are consistent before you change anything else.
Common Mistakes
- Setting peep height before you have a consistent anchor. Settle your anchor first, then place the peep.
- Serving too loosely, which lets the peep rotate or drift over time.
- Ignoring string stretch. Recheck peep height and alignment after the first several dozen shots.
- Choosing a tube that is too narrow for your lighting conditions.
- Adjusting the peep and sight at the same time, which makes it hard to tell what changed.
Recommended Gear
- Bow press: A press holds the bow at safe tension while you tie and adjust the peep. View on Amazon
- Serving thread: Good serving keeps the peep from creeping during shooting. View on Amazon
- Peep sight tubes: Choose a tube in the inside diameter that matches your sight pin and light conditions. View on Amazon
FAQ
Can I install a peep sight myself?
Yes, with a bow press and careful serving, most shooters can do it at home. If you are unsure about string tension or your bow’s manufacturer requirements, consult a qualified archery pro shop before you start.
How do I know if my peep height is right?
Your peep is set correctly when, at your normal anchor, the sight pin appears centered in the tube and your eye sits naturally behind it. Shoot a short series to check groups.
Will a peep sight make me more accurate?
A peep gives you a repeatable anchor and sight picture, which supports accuracy. Results still depend on form, release and practice.
Conclusion
A bow peep sight tube gives you a fixed reference point that makes every shot more repeatable. Choose a tube size that suits your light and eyesight, install it square and level, and confirm alignment at short range. Recheck it as your string settles, and you will have a sight picture you can trust.
Related reading
- Garmin Rangefinder Bow Sight: Setup, Calibration and Use Guide
- Why Do Archery Attack Bows and Arrows Miss? 6 Causes and Fixes
- Traditional Bow Arrow Rest: 7 Best Picks Compared for 2026
- Top 7 Archery Bow Arrow Rest Options Compared for Recurve and Compound Bows
- Top 3 Rip Shot Archery Release Aids Compared for Compound Bows
- Recurve Bow Arrow Rest Placement: A Step-by-Step Guide for Beginners
Ready to choose one?
