We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

Spot Hogg Edge Arrow Rest: Setup, Tuning and Tips for Beginners

Learn how to set up and tune a Spot Hogg Edge arrow rest, from mounting and centering to timing and common mistakes. A clear guide for new archers.

Updated November 2026

A Spot Hogg Edge arrow rest is a blade-style rest that holds the arrow on a thin, flexible contact point. Once it is mounted, centered and timed correctly, it lets the arrow leave the bow with minimal interference. This guide walks you through mounting, basic tuning and the mistakes that cause inconsistent groups.

What You Need Before You Start

Gather the right tools first so you are not improvising halfway through the install. Most setups take under an hour once you have everything on the bench.

Shopping for one? See our guide: Arrow Rest for Compound Bow: 6 Best Picks Compared (2026).

  • The rest, with its mounting bracket and included screws
  • A hex key set matching the screw sizes in the package
  • A drop-away or adjustable rest tool, if your model uses one
  • A bow square and a bow press, or a shop that can set your draw length
  • Arrows already cut to your draw length, with the correct spine
  • A target at 10 to 15 yards and a fletched arrow for paper tuning

How to Mount the Edge Rest on Your Bow

Start by attaching the rest bracket to the riser at the height your arrow shaft sits when nocked. Most archers set the rest so the arrow is level with the center of the bow, though some shooters adjust slightly for their form.

  1. Remove the old rest and clean the mounting area.
  2. Thread the bracket onto the riser, but leave the screws finger-tight.
  3. Set the rest height so the arrow sits level when nocked on the string.
  4. Tighten the screws evenly, checking that the bracket stays square to the bow.

Centering and Timing the Rest

Centering sets the arrow in line with the string so it does not drift left or right at release. Timing sets how far forward the arrow sits relative to the riser, which affects how it clears the bow.

Set the Center Shot

Use a bow square to check that the arrow aligns with the string at full draw. Adjust the rest left or right until the arrow sits straight over the string, then lock the center screw.

Check Rest Timing

Shoot a few arrows at 10 yards and watch how they behave. If the arrow leaves the rest too early or too late, the rest may need slight forward or backward adjustment. Make small changes, often one turn at a time.

Tuning With Paper

Paper tuning shows you how the arrow flies compared with the bow, and it is the best way to confirm your rest setup. Shoot an arrow through a sheet of paper stretched across a frame about three feet from the bow. The tear pattern reveals whether the arrow is spinning cleanly or fishtailing.

Tear Pattern What It Suggests Likely Adjustment
Fletching tear only, centered Arrow is flying straight No change needed
Tear high on the paper Arrow is nose-high at release Adjust rest height or nock point
Tear low on the paper Arrow is nose-low at release Adjust rest height or nock point
Tear to one side Arrow is left or right of center Adjust the rest center screw

Owners often report that small changes make a large difference in the paper pattern, so make one adjustment at a time and shoot again before changing anything else.

Common Mistakes to Avoid

  • Tightening the mounting screws before setting the height, which makes later adjustments harder.
  • Skipping the bow square check and relying only on the eye.
  • Changing several settings at once, which hides the effect of each change.
  • Using arrows with the wrong spine, which can cause tuning problems no rest adjustment will fix.
  • Ignoring wear on the rest contact point, which can change arrow flight over time.

For more on how rest styles compare, see Types of Arrow Rest: A Guide to Each Style for Archers. If you are sorting out where an arrow sits on the bow, Recurve Bow Arrow Rest Placement: A Step-by-Step Guide for Beginners covers placement in more detail.

A bow square is the simplest way to check centering and makes the initial setup far more accurate than eyeballing it.

View on Amazon

A hex key set in the correct sizes helps you tighten the bracket without stripping screws during adjustments.

View on Amazon

Fletched paper tuning kits make it easy to check arrow flight at home before you head to the range.

View on Amazon

FAQ

Do I need a bow press to install a Spot Hogg Edge rest?

A bow press is not strictly required for mounting the rest itself. However, you will need a reliable way to set your bow and draw length, so many archers use a shop or a press for initial tuning.

How far off can the center shot be before it matters?

Even a small misalignment can cause visible fishtailing and inconsistent groups. Use a bow square and paper tuning to confirm the arrow tracks straight, rather than relying on a fixed measurement.

How often should I check the rest after setup?

Check the mounting screws and rest contact point regularly, especially after long shooting sessions. Retune whenever you change arrows, string or draw length.

Conclusion

A Spot Hogg Edge arrow rest is simple to mount once you work through height, centering and timing in order. Paper tuning confirms the setup, so take your time with small adjustments. Consult a qualified archery pro shop if your bow or draw length needs professional setup.

Ethan Brooks

About Ethan Brooks

Ethan Brooks is part of our editorial team and reviews and edits our target archery guides, checking product details against manufacturer specifications and owner feedback.

About the author

Ethan Brooks
Ethan Brooks

Ethan Brooks writes reviews and buying guides for Archery Society.