Truglo Drop Away Arrow Rest Installation: 6 Steps for a Clean Setup
Learn truglo drop away arrow rest installation step by step, from mounting and cable routing to timing and tuning, so your arrow leaves the rest cleanly.
Updated November 2026
A truglo drop away arrow rest installation comes down to five things: mounting the rest at the correct height and centershot, routing the cable so the arm drops freely, setting the drop timing, and confirming the arrow clears the rest on release. Done in order, the whole job takes most archers under an hour with basic hand tools. This guide walks through each stage so your rest holds the arrow until release and then gets out of the way.
Before You Start: Tools and Preparation
Gather everything before you touch the bow. Working on a bow with the rest half attached is how threads get stripped and cables get kinked.
Shopping for one? See our guide: Drop Away Arrow Rest: 5 Best Picks Compared for Compound Bows (2026).
- Allen (hex) keys matching the rest’s mounting and adjustment screws
- A bow square or a ruler for measuring the arrow shelf
- A bow press or a helper to hold the bow steady
- Painter’s tape to mark your height and centershot reference points
- A dedicated drop away arrow rest instruction sheet for your exact model
Check the manufacturer’s instructions for your specific rest first. Setup details vary between models, and the steps below cover the general process.
Mounting the Rest and Setting Height and Centershot
- Attach the rest bracket to the riser. Use the mounting holes that fit your bow. Snug the screws but do not fully tighten them yet.
- Set the arrow shelf height. Nock an arrow and mark where the shaft sits relative to the bow’s sight window. Most archers start with the rest so the arrow is level or slightly low on the shelf, then fine-tune during testing.
- Set centershot. Measure from the arrow shaft to the riser’s center line. Adjust the rest left or right until the arrow sits centered over the riser. A starting point of roughly centered is usually close enough for a first shoot.
- Lock everything down. Tighten the mounting screws evenly, then recheck height and centershot.
Routing the Cable and Setting Drop Timing
The cable is what makes the rest work. A poorly routed cable can snag, drop the arrow early, or drop it late and cause a noisy release.
- Attach the cable to the rest’s arm and the cable slide or bracket. Keep the cable free of twists.
- Route the cable along the riser without contact. Keep it clear of the string, cams, and the bow’s limbs at full draw.
- Set the drop timing. Most rests adjust through the cable slide or the drop arm position. The arm should begin dropping at or just after the string leaves the arrow, not before.
- Cycle the bow slowly. Draw and release several times with the bow unloaded or lightly loaded, watching the arm move. It should fall smoothly and fully clear the fletching.
Testing and Final Tuning
Once the rest is mounted and timed, test with arrows at a shooting distance. Start close, around 10 to 15 yards, so you can see clearly how the arrow behaves. Watch for these signs:
| What you see | Likely cause | Adjustment |
|---|---|---|
| Arrow falls off the rest before release | Drop timing too early or cable too tight | Slacken the cable or move the timing setting later |
| Loud rest noise or vibration | Arm drops too late or hits the arrow | Shorten the cable or adjust the drop point earlier |
| Arrows fly left or right | Centershot off | Shift the rest in small increments |
| Fletching brushes the rest | Shelf height or arm clearance | Raise or lower the shelf slightly |
Make one change at a time and shoot a group after each adjustment. Changing several settings at once makes it hard to tell which one helped.
Common Mistakes to Avoid
- Tightening the mounting screws before checking centershot and height.
- Letting the cable rub against the string or limbs, which causes wear and inconsistent drop.
- Skipping the slow cycling test and going straight to live shooting.
- Over-tightening the cable, which can pull the arm out of its resting position.
- Ignoring a noisy release. Noise usually points to a timing or cable problem worth fixing before you shoot more arrows.
Recommended Gear
- Bow press: Holds the bow steady so you can work on the rest without stressing the limbs or cables. View on Amazon
- Hex key set: Covers the screw sizes most rests use, so you do not strip fasteners. View on Amazon
- Bow square: Helps verify arrow alignment and centershot more accurately than eyeballing it. View on Amazon
FAQ
How long does a truglo drop away arrow rest installation usually take?
Most archers finish the mounting, cable routing, and timing in under an hour. Testing and fine-tuning can take longer, since each adjustment needs a few shots to confirm.
Do I need a bow press for installation?
A bow press is not strictly required, but it makes the job safer and easier because it keeps the bow stable while you work on the cable and rest.
What if my arrows still fall off the rest after installation?
Check the cable first. A cable that is too tight or drop timing set too early is the most common cause. If problems continue, consult a qualified archery pro shop for hands-on help.
Conclusion
A careful truglo drop away arrow rest installation comes down to setting height and centershot first, routing the cable cleanly, and then timing and testing in small steps. Take your time with each stage and confirm every change with a few shots. Once the rest drops quietly and clears the fletching every time, you are ready to shoot with confidence.
Related reading
- Quietest Drop Away Arrow Rest: 7 Best Picks Compared (2026)
- How to Install a Drop Away Arrow Rest: 6 Steps for a Quiet, Clean Shot
- How Does a Drop Away Arrow Rest Work? A Step-by-Step Guide
- Drop Away Arrow Rest vs Whisker Biscuit: Which Should You Choose?
Ready to choose one?
