How to Install Arrow Rest on Compound Bow: A Step-by-Step Guide
Learn how to install arrow rest on compound bow with this step-by-step guide covering tools, mounting, centering and a quick check before you shoot.
Updated November 2026
To install an arrow rest on a compound bow, you mount the rest on the riser at the correct height, set its position so the arrow sits centered over the bow’s shelf, and secure it firmly. Most installs take under 30 minutes with basic hex keys. The steps below walk you through preparation, mounting, centering and a final check so the rest holds its position under load.
Gather Your Tools and Check Your Bow
Before you start, confirm your rest fits your bow. Most compound bows use a standard mounting hole pattern, but many rests require a specific hex key size. Read the rest’s instructions and check your bow’s manual for any manufacturer-specific guidance. For a broader overview of rest styles, see Compound Bow Arrow Rest Types: 5 Best Picks Compared (2026).
Shopping for one? See our guide: Arrow Rest for Compound Bow: 6 Best Picks Compared (2026).
- Hex keys matching the rest and sight mounting screws
- A drop of threadlocker (medium strength) for permanent installs
- A tape measure or ruler
- A clean, dry bow with the shelf free of grease
- A bow square or a fletched arrow for centering
Unstring the bow if you are removing an old rest, and keep the bow in a stable stand while you work.
Mount the Rest at the Correct Height
Start by attaching the rest’s base to the riser’s mounting holes, but leave the screws finger-tight. Most archers set the rest so the arrow shaft sits about level with the center of the sight and roughly centered on the arrow’s nock point. Many bow manufacturers give a starting height in the manual, so use that as your baseline.
- Hold the rest against the riser and check that the arrow will clear the riser when drawn.
- Tighten the mounting screws gradually and alternate between them to keep the base level.
- Confirm the rest sits flush against the riser without rocking.
Center the Rest Over the Shelf
Centering the rest is what keeps your arrow flight straight. Nock an arrow on the string, then check the arrow’s alignment from the back of the bow. The arrow should sit on the center of the shelf, with the fletching clearing the riser on both sides.
Make small horizontal adjustments, then recheck. Many rests use a windage screw or slotted mounting hole for this. Move in increments of about 1/32 inch and check after each change, since small shifts have a large effect at distance.
Set the Arrow Clearance
Once centered, check that the fletching clears the riser by at least a few millimeters at full draw. If the arrow touches the riser, the rest is set too far in.
Secure, Test and Fine-Tune
When the rest is centered and at the right height, tighten every screw fully. For permanent installs, apply threadlocker to the mounting screws. Then re-string the bow and shoot a few arrows at close range, watching for tears on the fletching or arrows that fly off target.
If your arrows show consistent left or right tailing, adjust the rest slightly and retest. For detailed tuning help, see Compound Bow Arrow Rest Adjustment: A Step-by-Step Guide for Beginners.
Common Mistakes
- Tightening screws before centering, which makes later adjustment harder
- Skipping threadlocker on rests that vibrate loose
- Setting the rest too far from the riser, which causes arrow instability
- Mounting the rest on a greasy or dirty shelf, which lets it slip
- Assuming one height works for all arrow lengths and point weights
Recommended Gear
A quality hex key set in metric and standard sizes makes mounting and adjustment easier. View on Amazon
A bow square helps you check centering accurately before you shoot. View on Amazon
FAQ
Do I need threadlocker to install an arrow rest?
It is not required, but it helps prevent screws from loosening from vibration. Use a medium-strength product if you want the rest to stay put long term.
How do I know if my arrow rest is centered?
Nock an arrow and check that it sits on the center of the shelf, with the fletching clearing the riser evenly on both sides. A bow square can help you verify alignment.
Can I install an arrow rest myself?
Yes, most archers can install a rest with basic hex keys and the manufacturer’s instructions. If you feel unsure about setting the bow’s draw or tuning, consult a qualified archery pro shop.
Conclusion
Installing an arrow rest on a compound bow comes down to clean mounting, correct height and accurate centering. Take your time with each step and recheck clearance after tightening. A properly installed rest gives you more consistent arrow flight and better accuracy.
Related reading
- Top 7 Archery Bow Arrow Rest Options Compared for Recurve and Compound Bows
- How to Install an Arrow Rest: A Step-by-Step Guide for Beginners
Ready to choose one?
