We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

Nock on Arrow Rest: How to Set It Up Correctly for Clean Arrow Flight

Learn how to get the nock on arrow rest right: nock height, timing, clearance checks and common fixes so your arrows fly clean and true.

Updated November 2026

The nock on arrow rest setup is the point where your arrow leaves the bow, so small errors here show up as erratic groups and porpoising arrows. In this guide you will check nock height, confirm clearance, and verify that the arrow sits on the rest the way the bow was designed to launch it. None of this requires special tools, only a steady bow, a square and a bit of patience.

Check Nock Height Before You Touch the Rest

Nock height is the distance from the arrow shelf to the nock groove on the arrow. Most manufacturers set the rest so the arrow sits level when nocked, which means the nock should point straight at the target with the arrow shaft parallel to the sight line. Start by nocking an arrow with your normal release and looking at the shaft from the side. If the nock tilts up or down, adjust the rest height or the nock position before doing anything else.

Shopping for one? See our guide: Arrow Rest for Compound Bow: 6 Best Picks Compared (2026).

Set Rest Position and Timing

Next, confirm the rest is centered and that the arrow clears the riser and the rest arms by a consistent margin. For drop-away rests, check that the arm retracts fully at full draw. Mark the arrow shelf with a pencil if it helps you spot movement. Then:

  1. Nock an arrow and draw the bow slowly to full draw, watching the fletching clearance.
  2. Release and check whether the arrow falls cleanly off the rest or catches on a fletch.
  3. Repeat with 10 to 15 shots, adjusting the rest in small increments until the arrow exits without contact.

Verify Clearance and Arrow Contact

Arrow contact with the rest should be light and even. Look for scuffs on the shaft or fletching after a shooting session, since heavy marks often point to a rest that is too low, too far in, or mounted at an angle. Check that the nock fits snugly on the string without twisting, and that the rest does not pinch the shaft when you release. If the arrow flexes against the rest, the spine or point weight may not match the bow, so recheck your arrow selection before making large rest changes.

Recognize When the Setup Is Right

A correctly set nock on arrow rest produces a clean launch with no visible wobble at 10 to 20 yards. Paper tuning is the most reliable check: the hole should appear centered, and tears should point in a consistent direction. If you see fish-tailing or a torn tail, adjust the rest or nock height in small steps and retest. Make one change at a time so you know which adjustment caused the result.

Common Mistakes

  • Adjusting the rest and the nock height at the same time, which makes results impossible to read.
  • Ignoring arrow spine and point weight while chasing rest position.
  • Letting the nock sit loose on the string, which changes nock height shot to shot.
  • Tightening rest screws so far that the mount flexes or strips.
  • Skipping a check after replacing string or cables, since string changes alter nock position.
  • Bow square: useful for checking that the nock and rest sit at the correct angle relative to the riser. View on Amazon
  • Paper tuning kit: a simple tuning frame lets you see arrow flight clearly after each rest adjustment. View on Amazon
  • Nock pliers: help you seat and reposition nocks consistently without damaging the arrow end. View on Amazon

FAQ

How do I know if my nock height is too high?

If the arrow rises at the back and drops at the front during flight, or if the nock looks tilted up when nocked, the nock height is likely too high. Lower the rest or reposition the nock and retest at 10 yards.

Does the nock on arrow rest setup change with different arrows?

Yes. Changes in spine, length or point weight can shift how the arrow leaves the rest, so recheck clearance whenever you change arrows.

Should I consult a professional for rest setup?

For most adjustments a careful self-check works well. If you see persistent damage to the arrow, the rest or the bow riser, or if your bow is under warranty, consult a qualified archery pro shop before continuing.

Conclusion

A well-set nock on arrow rest gives you a clean, repeatable launch that makes tuning far easier. Work through nock height, clearance and paper tuning in that order, changing one variable at a time. Once the arrow leaves the rest cleanly, your groups will tighten up and your bow will feel more consistent.

Ethan Brooks

About Ethan Brooks

Ethan Brooks is part of our editorial team and reviews and edits our target archery guides, checking product details against manufacturer specifications and owner feedback.

About the author

Ethan Brooks
Ethan Brooks

Ethan Brooks writes reviews and buying guides for Archery Society.