We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

Installing an Arrow Rest: A Step-by-Step Guide for Beginners

Learn installing an arrow rest step by step: mounting, centering, timing and tuning basics so your arrows fly straight from your first shot on the range.

Updated November 2026

Installing an arrow rest means mounting a small shelf or launcher on your bow’s riser so your arrow sits in the right spot and leaves the bow cleanly. Done correctly, the rest holds the arrow steady until release and lets it clear the riser without contact. This guide walks you through the setup so you can get your first accurate groups without guesswork.

What You Need Before You Start

Gather your tools before you touch the bow. Most rests mount with the hardware supplied in the box, but a few basics make the job easier.

Shopping for one? See our guide: Arrow Rest for Compound Bow: 6 Best Picks Compared (2026).

  • Your bow, unstrung or strung with a bow press, depending on the rest type
  • The arrow rest and its included screws, shims or spacers
  • A hex key set that matches the mounting hardware
  • A bow square or a ruler for measuring the arrow shelf height
  • Your arrows, cut to length and fletched

Step-by-Step: Mounting the Rest

  1. Check the mounting holes. Confirm the riser has the threaded holes your rest requires. Compound bows usually use a standard pattern, while traditional and recurve riser setups vary.
  2. Attach the rest loosely. Thread the screws in finger-tight so the rest can still slide and pivot.
  3. Set the arrow shelf height. Place your arrow on the shelf and check that the shaft sits centered on the bow’s center shot line. Most manufacturers give a starting height for the shelf, so follow their numbers before fine-tuning.
  4. Center the rest. Use a bow square or ruler to position the rest so the arrow lines up with the riser. The arrow should sit centered from the front of the bow, not sitting off to one side.
  5. Tighten the hardware. Snug all screws evenly, then torque them to the amount the manufacturer specifies. Overtightening can strip threads or crack housings.

Setting Up Timing and Clearance

Once the rest is mounted, check that the arrow has room to leave the bow. Draw the bow slowly and watch the nock and fletching. The arrow should not contact the rest or riser at any point during the draw or release.

For drop-away rests, confirm the arm drops away fully at full draw. For launcher-style rests, check that the arms or flippers are set to the right tension so they flex without binding the shaft.

Next Steps: Tuning for Accuracy

A rest in the right place is the starting point, not the finish. Shoot a few arrows at close range, then adjust the rest left, right, up or down in small increments based on where the arrows land. Paper tuning, using a sheet of paper stretched across a frame, shows arrow flight clearly. Consult your bow’s manual or a certified archery pro if you are unsure about tuning a compound or traditional setup.

Common Mistakes

  • Skipping the centering step and assuming the rest is aligned because it looks close.
  • Tightening screws before confirming the shelf height and position.
  • Ignoring clearance, which can cause fletching to clip the rest and throw arrows off target.
  • Using arrows with the wrong spine or length for the rest type.
  • Changing several settings at once, which makes it hard to know what fixed the problem.
  • Bow square: A square checks rest centering and cant faster than eyeballing it. View on Amazon
  • Hex key set: A full set matches the screw sizes on most rests and prevents stripped heads. View on Amazon
  • Paper tuning kit: A paper frame makes it easy to see arrow flight and confirm your rest adjustments. View on Amazon

FAQ

Do I need a bow press to install an arrow rest?

Not always. Many rests mount to a strung bow, but some setups require the bow unstrung or pressed, so check the manufacturer’s instructions first.

How do I know if my rest is centered?

Use a bow square or ruler to measure from the riser to the arrow shaft at the rest position. The arrow should sit at the same distance from the riser edge as the center shot line you measured.

Why is my arrow still hitting the rest after installation?

The rest may sit too far in or too far out, or the shelf height may be off. Adjust in small steps and recheck clearance at full draw.

Conclusion

Installing an arrow rest comes down to mounting it securely, centering it on the shot line and confirming clearance at full draw. Once it is in place, tune the rest with a few test shots and small adjustments. Take your time with each step and your arrows will start flying where you aim.

Ethan Brooks

About Ethan Brooks

Ethan Brooks is part of our editorial team and reviews and edits our target archery guides, checking product details against manufacturer specifications and owner feedback.

About the author

Ethan Brooks
Ethan Brooks

Ethan Brooks writes reviews and buying guides for Archery Society.