We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

What Are 1st, 2nd and 3rd Axis on a Bow Sight? A Beginner’s Guide

Learn what 1st, 2nd and 3rd axis on a bow sight mean, why your pins drift off target, and how to level and adjust each axis for accurate shooting.

Updated November 2026

The 1st, 2nd and 3rd axis on a bow sight describe the three directions a sight can tilt or rotate relative to the bow. Getting each one level and square is what keeps your pins aligned across distances, so an archer who ignores them often chases pin gaps that are really a mounting problem.

What Each Axis Controls

The 1st axis is side-to-side rotation around the vertical plane. If the sight is tilted left or right, your pins will look fine up close but drift sideways as you move farther away. The 2nd axis is forward and backward tilt, which mainly changes how the pins line up vertically as distance changes. The 3rd axis is rotation of the sight around the arrow’s line of flight, often called cant. A sight that is canted will shift your groups even when the pins look correct on the target.

Shopping for one? See our guide: Bow Sights with Rangefinder: 5 Best Picks Compared (2026).

Manufacturers typically describe these as adjustments on the sight bracket or mounting bar, and the exact knobs and screws vary by model. Check your sight’s manual for the specific adjustment points before you start turning anything.

Why Your Sight Drifts Off Level

Most axis problems come from one of three sources: a bracket that was not tightened evenly, a bow that was bumped or stored against a wall, or a sight that was moved between bows without re-leveling. Vibration from shooting can also loosen a mounting screw over a few hundred shots. Because the three axes interact, correcting one can throw off another, so it helps to adjust them in order rather than all at once.

How to Check and Adjust Each Axis

  1. Use a bubble level or a plumb line on the bow’s riser to confirm the bow is vertical when you hold it at full draw.
  2. Set the sight so the top pin is directly above the arrow in your sight window, then check that the pin column runs parallel to the arrow.
  3. Adjust the 3rd axis first (cant) so the pins sit square to the arrow. A common check is to hang a plumb line along the sight housing.
  4. Adjust the 1st axis (side-to-side) so the pin column is centered on the riser, then confirm the pins stay aligned at close and far distances.
  5. Adjust the 2nd axis (tilt) last, since it has the most influence on vertical pin spacing across distances.
  6. Shoot a few groups at 20 yards, then re-check each axis before making any pin changes.

If a sight keeps drifting after you have leveled it, the mounting bracket or sight extension may be worn. Replacing worn hardware is usually simpler than repeated adjustments.

Tips for Staying Level

  • Tighten bracket screws in small, even steps rather than fully tightening one side first.
  • Re-check levels after the first 50 shots, since settling often happens early.
  • Store the bow in a stand or case so the sight is not knocked out of square.
  • If you change bows, re-level the sight from scratch rather than assuming the old settings carry over.

For related setup steps, see Mounting a Bow Sight: A Step-by-Step Guide for Beginners and Single Pin or Multi Pin Bow Sight (2026): Which Is Better for Beginners?, which covers how pin count interacts with alignment.

What We’d Use

A simple bubble level that clips onto the sight bar or riser makes checking the 1st and 3rd axes much faster. Search for View on Amazon to find models designed for archery mounting.

A plumb line kit gives a reliable vertical reference when you check cant. Search for View on Amazon to compare options.

FAQ

Which axis should I adjust first?

Start with the 3rd axis (cant), then the 1st, and finally the 2nd. Adjusting in that order keeps the changes from undoing each other.

Why do my pins look fine up close but miss at longer distances?

This usually points to a 1st or 2nd axis problem. A sight tilted side-to-side or forward-back will show its error more as distance increases.

Do I need special tools to level a bow sight?

A bubble level and a plumb line are enough for most setups. If you are unsure about making adjustments on a valuable bow, consult a qualified archery pro shop for help.

Ethan Brooks

About Ethan Brooks

Ethan Brooks is part of our editorial team and reviews and edits our target archery guides, checking product details against manufacturer specifications and owner feedback.

About the author

Ethan Brooks
Ethan Brooks

Ethan Brooks writes reviews and buying guides for Archery Society.