TruGlo Lock Fire Arrow Rest: Setup Steps and Tuning Tips
Learn how to set up and tune a TruGlo Lock Fire arrow rest, from mounting and cable tension to nock height and arrow clearance. A clear guide for new archers.
Updated November 2026
The TruGlo Lock Fire arrow rest is a drop-away style rest that holds your arrow until the shot, then drops out of the way. This guide walks you through mounting it, setting cable tension and checking clearance so your arrow flies clean. Most of the work is in the setup, so take your time with each step.
What You Need Before You Start
Gather these items before you begin, so you are not stopping halfway through the install:
Shopping for one? See our guide: Arrow Rest for Compound Bow: 6 Best Picks Compared (2026).
- Your bow, unstrung and on a stable stand or bow vise
- The arrow rest with its mounting hardware and cable assembly
- A hex key set and a small screwdriver
- A bow square and a clean, straight arrow of your draw length and spine
- Paper, tape or a rest-setting tool, if you plan to check centershot
If you are new to rests in general, the overview in Types of Arrow Rest: A Guide to Each Style for Archers explains how drop-away designs differ from other styles.
Step-by-Step Setup for the TruGlo Lock Fire Arrow Rest
Step 1: Mount the Rest to the Riser
Attach the rest body to the riser using the mounting holes on your bow. Leave the screws snug but not fully tightened, so you can adjust height and position. Check the manufacturer instructions for the correct hardware for your riser.
Step 2: Set the Cable Tension
The cable and its spring control how the rest holds and releases the arrow. Set the tension according to the manufacturer’s guidance for your draw weight. A cable that is too loose can let the arrow drop early, while one that is too tight can cause the rest to release sluggishly.
Step 3: Set Nock Height and Centershot
Position the rest so the arrow sits level with the shelf, then check centershot with a bow square. Move the rest left or right until the arrow is centered over the riser at full draw. Small adjustments matter here, so move the rest in tiny increments.
Step 4: Check Arrow Clearance
Nock an arrow and draw the bow slowly, watching how the arrow sits on the rest. Shoot a few arrows at close range and confirm that the rest drops cleanly and the arrow clears the riser and the fletching clears the rest arm. If the fletch contacts the rest, adjust your rest position or check the fletch alignment.
Tuning for Clean Arrow Flight
Once the rest is mounted, tune the setup with paper or a bare-shaft test. Shoot through paper at a short distance and read the tear. A bow that is out of tune will show a tear that points in a consistent direction, and you adjust the rest in small steps until the tear is clean. For a broader tuning routine, see Spot Hogg Edge Arrow Rest: Setup, Tuning and Tips for Beginners, which covers the same tuning concepts across a different rest style.
A drop-away rest is only as good as its timing. Make sure the rest releases at the right moment in the shot cycle, and recheck the cable after your first few sessions, since it can settle and loosen.
Common Mistakes to Avoid
- Tightening the mounting screws before setting height and centershot.
- Setting cable tension by feel instead of following the manufacturer’s guidance.
- Skipping the paper test and assuming the rest is tuned.
- Ignoring fletch clearance, which can cause inconsistent arrow flight.
- Forgetting to recheck the setup after changing arrows, strings or draw length.
Recommended Gear
A bow square makes centershot checks far more accurate than eyeballing the rest position. View on Amazon
A tuning or paper-tuning kit helps you read arrow flight and make small adjustments with confidence. View on Amazon
A bow vise or stand holds the bow steady while you mount and adjust the rest, which keeps the work safer and more precise. View on Amazon
FAQ
Is the TruGlo Lock Fire arrow rest suitable for beginners?
It can be, but expect to spend extra time on setup and tuning. Beginners often benefit from having an experienced archer or a pro shop check the install.
How often should I check the cable tension?
Check it after your first several sessions and then periodically, since cables can settle over time. Follow the manufacturer’s guidance for adjustment.
What if my arrows are still hitting the rest after setup?
Recheck nock height, centershot and fletch clearance. If the problem continues, consult a qualified archery technician.
Conclusion
Setting up the TruGlo Lock Fire arrow rest comes down to careful mounting, correct cable tension and patient tuning. Work through each step in order and make small adjustments. A well-tuned rest gives you clean drop-away every shot.
Related reading
Ready to choose one?
