We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

Truglo Bow Sight Light Battery Replacement: Step-by-Step Guide

Learn how to replace the truglo bow sight light battery safely, with steps for checking the sight, swapping the cell and testing the pin light before you shoot.

Updated November 2026

Replacing the battery in a TruGlo bow sight light takes about five minutes with the right cell and a clean workspace. This guide walks you through confirming the battery is the problem, removing the old cell, installing the new one and checking that the light works before your next session. Battery specifics vary by model, so always confirm the type printed on your sight or in its manual.

Confirm the Battery Is the Problem

Before you open anything, make sure the battery is actually the cause. Dim or flickering pins often come from a worn cell, but a dirty lens, a loose fiber optic or a switch that is not fully seated can produce similar symptoms. Turn the light on in a dark area and look for a steady, bright glow at the pin tip. If the glow fades within a few minutes of use or disappears when you tap the sight housing, a dead or weak battery is the likely cause.

Shopping for one? See our guide: Bow Sights with Rangefinder: 5 Best Picks Compared (2026).

Replacing the Battery Step by Step

Work on a clean, flat surface and keep small parts from rolling away. Set the bow down or rest it on a stable stand so the sight does not get bumped during the process.

  1. Locate the battery cap on the sight housing. On most TruGlo light assemblies it is a small threaded or press-fit cap near the light module.
  2. Turn the cap counterclockwise slowly until it comes free. Do not force it. If it resists, stop and check whether it is a press-fit style that needs gentle pressure to release.
  3. Remove the old battery and note its orientation. The positive end usually faces outward, toward the cap, but confirm this against the markings inside the housing.
  4. Wipe the battery contacts with a dry cloth. If you see white or green residue, clean it gently with a cotton swab lightly dampened with isopropyl alcohol and let it dry completely.
  5. Insert the new battery in the same orientation as the old one. Use a fresh cell of the type specified for your model.
  6. Replace the cap and tighten it until it is snug. Overtightening can crack the housing or damage the seal, so finger-tight plus a small turn is enough.
  7. Turn the light on and check the pin glow in a dark room before heading to the range.

Testing the Light and Protecting the Sight

After installation, cycle the light through its brightness settings if your model has them. Confirm that each pin illuminates and that the glow is even. Check that the fiber optic is still seated against the pin housing, because a shifted fiber can look like a battery problem even after the cell is fresh.

Store your bow with the light switched off to extend battery life. Keep spare batteries in a dry, cool place rather than in a hot car, because heat shortens the life of many small cells. If you notice corrosion, moisture inside the housing or a light that will not turn on with a new battery, stop using the sight and contact TruGlo support or a qualified bow technician for service.

Common Mistakes

  • Installing the battery backward, which leaves the light dead even though the cell is new.
  • Overtightening the battery cap, which can crack the housing or strip threads.
  • Skipping contact cleaning, so corrosion keeps the circuit from completing.
  • Assuming a dim pin is always the battery when the fiber optic has shifted.
  • Leaving the light on after shooting, which drains the cell faster than most archers expect.

A fresh cell of the exact type listed for your sight is the most important item. Check the battery designation printed on your housing or in the manual before buying.
View on Amazon

A small set of precision screwdrivers or a cap wrench helps with threaded battery caps and keeps you from marring the finish.
View on Amazon

Isopropyl alcohol and cotton swabs are useful for cleaning battery contacts without leaving residue.
View on Amazon

FAQ

How long does a TruGlo bow sight battery last?

Battery life depends on how often you use the light and at what brightness. Many archers replace the cell once the pins begin to dim, and switching the light off between shooting sessions extends its life considerably.

Can I use a rechargeable battery in my sight?

Only if the voltage and size match what the manufacturer specifies. Mismatched cells can underperform or damage the circuit, so confirm compatibility before swapping.

What if the light still does not work after changing the battery?

Check battery orientation, clean the contacts and confirm the fiber optic is seated. If the light remains dark, contact TruGlo support or a qualified technician rather than opening the housing further.

Conclusion

Replacing a TruGlo bow sight light battery is a quick task when you confirm the cell is the cause and follow the steps carefully. Check orientation, clean the contacts and test the pins before you go shooting. A little routine care keeps your sight reliable through the season.

Ethan Brooks

About Ethan Brooks

Ethan Brooks is part of our editorial team and reviews and edits our target archery guides, checking product details against manufacturer specifications and owner feedback.

About the author

Ethan Brooks
Ethan Brooks

Ethan Brooks writes reviews and buying guides for Archery Society.