TruGlo Bow Sight Battery Replacement: A Step-by-Step Guide
Learn how to do truglo bow sight battery replacement safely, including battery type, pin cleanup, and a quick function check before your next shoot.
Updated November 2026
A truglo bow sight battery replacement is a simple job that takes a few minutes and keeps your pins lit when you are shooting in low light. This guide walks you through identifying the right battery, removing the old one without damaging the housing, and testing the sight before you head back to the range. Most of the work is careful handling rather than tools.
What You Need Before You Start
Check the sight’s manual or the battery compartment label to confirm the battery size. Many TruGlo fiber-optic and LED sights use a common coin-cell style battery, but models differ, so match the number printed on the old cell rather than guessing. Keep these items within reach:
Shopping for one? See our guide: Bow Sights with Rangefinder: 5 Best Picks Compared (2026).
- A replacement battery of the exact size specified for your sight
- A small flathead screwdriver or a plastic trim tool for opening the cap
- A soft cloth to protect the sight face and keep grit out
- A pencil eraser or a dry cotton swab for cleaning battery contacts
- Good light and a clean, flat surface
Step-by-Step Battery Replacement
- Power down the sight. If the illumination is on, switch it off first so you do not drain the new cell during the swap.
- Open the battery compartment. Place the cloth down, then turn the cap or pull the battery housing out gently. Use the screwdriver only on a slotted cap, and turn slowly to avoid slipping.
- Note the battery orientation. Look at which side faces up before removing the old cell. Taking a photo with your phone works well for this.
- Clean the contacts. Wipe the spring and the battery seat with a dry swab. Remove any corrosion or residue, since a dirty contact often causes a dim or flickering pin even with a fresh battery.
- Insert the new battery. Place it with the positive side facing the orientation you noted. Seat it fully and avoid forcing it.
- Close the compartment. Thread the cap back on or press the housing in until it seats. Do not overtighten plastic threads.
Testing the Sight After Replacement
Turn the illumination on and check each pin in a dim room and in daylight. Each pin should light evenly at the brightness you normally use. If one pin stays dark, remove the battery, clean the contacts again, and reseat it. Recheck the housing for any sign of moisture, which can cause a short.
Storage and Battery Care
If you will not shoot for several weeks, remove the battery to prevent leakage from damaging the contacts. Keep spare batteries in a dry place away from heat, and record the date you installed each one so you can replace them on a regular schedule rather than waiting for the light to fade mid-session.
Common Mistakes
- Installing the battery backward, which can leave the light off with no obvious fault
- Using a battery of the wrong size or chemistry for your model
- Skipping contact cleaning and blaming the new battery for a dim pin
- Overtightening the cap, which can crack the housing or strip the threads
- Leaving a battery in a sight that will sit unused for months
Recommended Gear
A small set of precision screwdrivers makes opening battery caps far easier and reduces the risk of scratching the housing. View on Amazon
Fresh coin-cell batteries in the exact size your sight requires keep your setup reliable on the range. View on Amazon
Lint-free cleaning swabs are useful for wiping contacts without leaving fibers behind. View on Amazon
FAQ
How often should I replace a TruGlo bow sight battery?
Battery life depends on how often you use illumination and the cell type, so there is no fixed interval. Many archers replace the battery at the start of each season and carry a spare for tournaments or long outdoor shoots.
Can I use any coin-cell battery in my sight?
No. Confirm the size and voltage printed on the old battery or in the manual, since a mismatched cell may not fit properly or deliver steady power. Consult the manufacturer’s documentation or a qualified archery shop if you are unsure.
Why is one pin still dim after I replaced the battery?
The most common cause is a dirty or misaligned contact, so clean and reseat the battery first. If the pin still fails, the fiber or LED component may be damaged, and you should contact the manufacturer or a professional repair service.
Conclusion
A careful truglo bow sight battery replacement takes only a few minutes when you match the battery size, clean the contacts, and test each pin afterward. Keep spares on hand and note the install date so you can change batteries before they fail during a shoot. Following these steps keeps your sight reliable session after session.
Related reading
- Garmin Rangefinder Bow Sight: Setup, Calibration and Use Guide
- Why Do Archery Attack Bows and Arrows Miss? 6 Causes and Fixes
- Traditional Bow Arrow Rest: 7 Best Picks Compared for 2026
Ready to choose one?
