STX Stallion 500 Arm Guard: How to Choose, Fit and Wear It Correctly
Learn how to size, fit and wear the stx stallion 500 arm guard correctly so it protects your forearm without slowing your draw or string-walk.
Updated November 2026
The stx stallion 500 arm guard is a forearm protector designed to shield your bow arm from string slap and keep your sleeve out of the string’s path. This guide shows you how to check fit, position the guard, and keep it comfortable through a full session. Most fit problems come from wrong strap tension or a guard sitting too high or too low, and both are easy to correct.
Check Your Sizing Before You Strap It On
Manufacturers generally size arm guards by forearm length and circumference rather than by a simple small-medium-large label. Measure your bow forearm from the inside of the elbow crease to the base of the wrist, then measure the circumference at the widest point of the forearm with the arm relaxed. Compare both numbers against the size chart printed by STX before ordering or wearing a guard. If you fall between two sizes, the larger size usually fits better over a heavier jacket, while the smaller size keeps the guard from sliding during the shot.
Shopping for one? See our guide: Maverik Max Arm Guard Review (2026): Features and Performance.
Position the Guard Correctly
Place the guard on the inside of your bow forearm, with the leading edge sitting about two to three finger-widths below the elbow. The guard should cover the area where the string travels after release, not the wrist or the elbow joint. Extend your bow arm fully and look down the forearm: the guard should sit centered over the muscle belly without pulling the sleeve tight. If you can see the string pass directly over bare skin during a practice shot, the guard is too low or too far to one side.
Adjust Strap Tension
Secure the strap snugly enough that the guard does not rotate when you flex your wrist, but loose enough that you can feel your pulse in your forearm. A strap that cuts off circulation or leaves marks after ten minutes is too tight. Recheck the tension after your first few shots, since the material compresses slightly as it settles.
Test Your Setup Before a Full Session
Shoot a few arrows at close range to confirm the guard stays put. Draw, anchor and release several times, then look at where the guard sits. Check for these points:
- The guard does not shift upward toward the elbow during the draw.
- The string clears the guard cleanly on release with no contact on bare skin.
- Your sleeve does not catch on the guard or the string at full draw.
- Your wrist can still flex freely in the bow hand position.
- The strap stays fastened after ten to fifteen shots.
If any of these fail, adjust the position first and the strap second. Moving the guard a finger-width often fixes more than tightening.
Recommended gear
- Sleeve or shirt with a fitted cuff: A snug sleeve keeps loose fabric away from the string and works well under the stx stallion 500 arm guard. View on Amazon
- Replacement strap set: If the original strap wears out or loses grip, a spare set lets you keep the guard secure without replacing the whole unit. View on Amazon
FAQ
Should the stx stallion 500 arm guard be worn over or under a sleeve?
Most archers wear it over a thin, fitted sleeve so the guard sits directly on the arm and does not slide. A heavy jacket can bunch up under it, so test the position in what you plan to shoot in.
How do I know if the guard is too tight?
If your hand tingles, your fingers feel cold, or the strap leaves a deep indentation after a short session, loosen it. Good tension holds the guard in place without restricting blood flow. If numbness persists, stop shooting and consult a doctor. For a deeper look, 4 Best Stx Stallion 500 Arm Guard Lacrosse Arm Pads (2026): Our Picks covers this in detail.
Can I use the stx stallion 500 arm guard for other bow types?
The same positioning principles apply to recurve and compound bows, but check the string path on your specific setup. A longer or faster string may need the guard moved slightly higher or lower to clear the forearm.
Conclusion
Measure your forearm, position the guard two to three finger-widths below the elbow, and set the strap to hold without cutting off circulation. Test the setup with close-range shots before a full session. Once it stays put and the string clears your skin, the guard will do its job without distracting you.
Related reading
- STX Cell IV Arm Guard: How to Choose, Fit and Wear It Correctly
- Women's Archery Arm Guard: How to Choose and Fit One Properly
- Welding Arm Guard Pattern: How to Cut and Sew One (Step by Step)
Ready to choose one?
