Ripcord Code Red Drop Away Arrow Rest: Setup and Tuning Steps
Learn how to set up and tune a ripcord code red drop away arrow rest, from mounting and timing to cable tension and arrow clearance checks.
Updated November 2026
A ripcord code red drop away arrow rest holds your arrow on the riser during the draw and then drops it out of the way as the bow fires. Getting it right means mounting it square, setting the timing so the rest falls at the right moment, and confirming clean arrow clearance. This guide walks through those steps for new archers and explains what to check once the bow is shooting.
Before You Start: Tools and Preparation
Gather everything before you touch the bow. Working on a stable surface with good light saves time and prevents dropped parts.
Shopping for one? See our guide: Drop Away Arrow Rest: 5 Best Picks Compared for Compound Bows (2026).
- Hex keys matching the rest’s mounting hardware and the cable guard
- A bow square or straightedge for checking alignment
- A tape measure or ruler
- A cable-tension gauge or your bow manufacturer’s tuning guide
- Paper or a clean target face for paper tuning
- Bow stringer, if you need to remove the string
Check the manufacturer’s instructions for your specific bow model, since mounting holes and cable routing differ between brands. Refer to the bow’s owner’s manual for maximum draw weight and any warranty limits on modifications.
Mounting the Rest on the Riser
Attach the rest to the riser using the mounting holes that match your bow’s bracket pattern. Start the hardware by hand so the rest can still shift slightly. Position the rest so the arrow sits on the centerline of the bow, then tighten the screws evenly.
Use a bow square to confirm the rest sits level and at the correct height. The arrow should rest where your shooting plan puts the nock and shaft, with the cable guard clear of the arrow path.
Setting the Timing and Cable Tension
The drop-away mechanism is driven by a cable connected to the bow’s cam or limb system. The cable must be tensioned so the rest drops only after the arrow leaves the string. Too early and the arrow can deflect. Too late and the rest may strike the arrow during the shot.
Adjusting the Cable
- Loosen the cable clamp and set the cable length according to the manufacturer’s specifications.
- Draw the bow slowly and watch the rest. It should stay engaged through the draw and begin dropping as the string passes the arrow.
- Make small adjustments, retightening the clamp only after each change.
Checking Arrow Clearance
Once the rest drops, the arrow should have clear space above and beside it. Shoot a few arrows at close range and watch the rest return to its starting position after each shot. A rest that bounces back into the arrow path or rubs the fletching needs further tuning.
Paper Tuning for Clean Arrow Flight
Paper tuning shows whether the arrow leaves the bow straight. Shoot an arrow through a sheet of paper stretched on a frame about three feet from the bow. A tear pattern with the fletching tail at the center indicates correct arrow flight. Adjust the rest’s horizontal and vertical position in small increments if the tear shows the arrow is leaving at an angle. Recheck the timing after any position change, because the cable path can shift.
Common Mistakes
- Skipping the level check, which causes the arrow to sit crooked on the rest.
- Overtightening the cable clamp, which can strip threads or alter timing.
- Shooting before confirming the rest drops fully after each shot.
- Ignoring wear on the rest’s arm or cable, which can change timing over time.
- Making several adjustments at once, making it hard to know which change helped.
Recommended Gear
- A bow square helps you check mounting height and level quickly, which is the foundation of any reliable setup. View on Amazon
- A paper tuning frame gives you a consistent surface for checking arrow flight after each adjustment. View on Amazon
FAQ
Can I install a ripcord code red drop away arrow rest myself?
Yes, most archers can mount it with basic hex keys and a bow square. If the cable routing or timing feels unclear, have a pro archery shop check the setup before you shoot.
How do I know if my drop away rest timing is off?
Watch the rest while drawing and shooting slowly. If it drops too early, too late, or strikes the arrow, the cable tension needs adjustment.
Should I tune the rest after changing arrows?
Yes. Different arrow spine and length can change the arrow’s position on the rest, so recheck paper tuning and clearance after any arrow change. For more on related setups, see Drop Away Arrow Rest for Compound Bow: 7 Best Picks Compared (2026).
Conclusion
A well-mounted and properly timed drop away rest gives you clean arrow release and consistent accuracy. Work through the mounting, cable, and paper tuning steps in order, and make one adjustment at a time. For a broader look at options, read Ripcord Red Arrow Rest: 5 Best Picks Compared for 2026.
Related reading
- Quietest Drop Away Arrow Rest: 7 Best Picks Compared (2026)
- How Does a Drop Away Arrow Rest Work? A Step-by-Step Guide
- Drop Away Arrow Rest vs Whisker Biscuit: Which Should You Choose?
Ready to choose one?
