Peep Sight Bow Install: A Step-by-Step Guide for Beginners
Learn how to do a peep sight bow install in clear steps, from choosing the right spot on the string to checking alignment and tying in your peep safely.
Updated November 2026
A peep sight bow install means fitting a small circular sight into your bowstring so you have a consistent aiming reference every time you draw. Done correctly, the peep sits at the same spot on your anchor point and lines up with your sight or pins. This guide walks through the tools, the placement, and the final checks so the peep stays put and your shots stay repeatable.
What You Need Before You Start
Gather everything before you touch the string. Working with the bow unstrung or with the string relaxed keeps you from twisting the string or stressing the limbs.
Shopping for one? See our guide: Bow Sights with Rangefinder: 5 Best Picks Compared (2026).
- A peep sight with a bore size that matches your sight picture, typically a size you choose for your draw and eye
- Bowstring serving material or a peep tying tool
- Bow square or a measuring tape
- A bow press or a stand to hold the bow safely while you work
- Sharp scissors or a hobby knife for trimming thread
- Beeswax or a serving wax to protect the tied thread
Step-by-Step Peep Sight Bow Install
Step 1: Find the Right Height
Draw the bow to your normal anchor point with your release hand and let your eye settle naturally. Ask a helper to mark the string at the spot where the peep centers in your eye, or mark it yourself with a piece of tape while watching through the sight. Many archers find this point sits a little above the nock, but the correct position depends on your anchor and face shape, so check it in your own setup.
Step 2: Set the Peep Position
Unstring or relax the bow enough to work comfortably. Slide the peep onto the string at the marked spot, with the cutaway facing the correct direction. Most peeps have a marked side for orientation, and it should face you when you are at full draw. Keep the peep level and square to the string.
Step 3: Tie the Peep In Place
Wrap serving thread tightly above and below the peep, keeping the wraps snug so the peep cannot slide. Use a consistent number of wraps on each side and finish with a secure knot or serving tool locking. Apply a light coat of wax over the thread to protect it from moisture and friction.
Step 4: Check Alignment and Stability
Restring the bow and draw it back. Confirm the peep sits level, centered in your sight picture, and does not rotate under tension. If it turns or tilts, unstring and adjust the serving. Using a bow square helps confirm the peep is square to the string.
Common Mistakes to Avoid
- Tying the peep too loosely, which lets it rotate after a few shots
- Installing the peep at a height that does not match your anchor point
- Skipping the wax, which can let the serving loosen with moisture and wear
- Forgetting to check the peep orientation before finishing the wraps
- Drawing the bow hard with an unfinished or unchecked installation
Recommended Gear
A dedicated serving tool makes consistent wraps easier, especially for beginners. View on Amazon
Quality serving thread in a matching color keeps the peep neat and secure. View on Amazon
Related Guides
If you are still choosing hardware, the guide to Peep Sight for Bow Installation: A Step-by-Step Guide for Beginners covers the basics in more detail. For a sight that uses a lens, see Bow Peep Sight with Lens: How to Install and Aim One (Step by Step). If your peep keeps shifting after install, Peep Sight on Bow Keeps Twisting? How to Fix It Step by Step explains the most common causes.
FAQ
How high should a peep sight sit on the string?
It should center in your eye at full draw with your normal anchor. Mark the spot while drawing rather than relying on a fixed measurement, since anchor points vary between archers.
Can I install a peep sight without a bow press?
You can, but a stand or press makes it safer and keeps the limbs stable while you work. Never tie a peep on a bow you are holding with the string under tension.
How do I know if my peep is installed correctly?
At full draw, the peep should sit level, stay centered in your sight picture, and not rotate. If you see movement after several shots, retie the serving. Consult a qualified pro shop if you are unsure.
Conclusion
A solid peep sight bow install comes down to correct height, secure serving, and a final check at full draw. Take your time with the marking step, because placement drives everything that follows. Once the peep is set, recheck it after the first week of shooting to confirm it has held.
Related reading
- Bow Peep Sight Tube: How to Install and Align One (Step by Step)
- Bow Sight Without Peep: Setup Steps for Accurate Shots (2026)
- Bow Sight Mounting Screws: How to Install and Tighten Them Correctly
- Battery for Bow Sight Light: How to Choose, Install and Replace It
Ready to choose one?
