We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

New Hamskea Arrow Rest: Setup Steps and Tuning Tips for Beginners

Learn how to install a new Hamskea arrow rest, set the timing and tune it for clean arrow flight. Practical steps and common mistakes for new archers.

Updated November 2026

A new Hamskea arrow rest is only useful once it is mounted square to your bow, set to the correct height and tuned to your arrow. This guide walks you through the setup in the order that saves you the most time: prepare the bow, mount the rest, set the center shot and nock height, then check paper tune and bare-shaft tune. Follow these steps and you should be shooting with clean arrow flight and no fletching contact.

What You Need Before You Start

Gather your tools before you touch the bow. Working without them usually means stripping screw heads or guessing at measurements.

Shopping for one? See our guide: Hamskea Hybrid Hunter Pro Arrow Rest: 3 Best Picks Compared (2026).

  • A hex key set that matches the mounting hardware on your bow and rest
  • A bow square or straightedge for checking alignment
  • A tape measure or ruler marked in 1/16-inch increments
  • A paper tuning frame or a large sheet of paper and a stand
  • Your arrows, with the nock set and fletching in good condition
  • Thread-locking compound for the mounting screws (optional, but helpful)

Step 1: Mount the Rest and Set the Center Shot

Attach the rest to your riser using the mounting holes that match your bow’s sight window and draw length. Snug the screws but do not fully tighten them yet. Next, nock an arrow and check that the arrow sits centered between the cable and the riser, with the rest arm positioned so the arrow passes through without touching the rest arm on release.

Once the position looks right, tighten the screws evenly. Recheck the alignment after tightening, since mounting pressure can shift the rest slightly.

Setting the Rest Height

Set the rest so the arrow shaft sits level with the nock point on the string. Most archers start with the arrow centered in the rest arm and adjust the height until the shaft is parallel to the arrow shelf. Small changes matter here, so move the rest in very small increments and recheck after each adjustment.

Step 2: Check Nock Height and Arrow Positioning

Nock height controls how the arrow sits on the string. Clip the nock so it sits securely on the string serving without twisting. If the arrow tips downward or upward when nocked, the nock point is off, and the rest may not hold the arrow level.

Check that the arrow sits square to the rest and the fletching clears the rest arm. If a fletch brushes the arm when the bow is at full draw, adjust the rest or the arrow rotation before you shoot.

Step 3: Tune the Rest With Paper and Bare Shaft

Paper tuning shows you how the arrow leaves the bow. Shoot an arrow through a sheet of paper stretched on a frame about three feet from the bow. A torn hole with the fletching tear showing a clean tail suggests good arrow flight. If the tear shows a sideways tilt or the arrow tail drifts, adjust the rest and try again.

Bare-shaft tuning is a useful second check. Shoot a bare shaft (no fletching) and an arrow with fletching at the same distance. If the two arrows land in the same group, the rest and bow are tuned well. If the bare shaft lands well away from the fletched group, make small rest adjustments and repeat.

Common Mistakes

  • Tightening the mounting screws before checking alignment, which locks in the wrong position
  • Making large rest adjustments instead of small, measured changes
  • Ignoring nock height and blaming the rest for a problem caused by poor nocking
  • Skipping a recheck after the bow has been shot for several days, since settings can drift
  • Judging tune by a single shot instead of a group of several arrows

A bow square makes alignment checks far more reliable than eyeballing the setup, and a paper tuning frame gives you a consistent surface for tuning.

  • A bow square for checking the rest against the bow’s center line View on Amazon
  • A paper tuning frame with a clamp-on sheet holder for fast, repeatable paper tests View on Amazon

For more background on how rests hold arrows and how different designs compare, see What Holds Arrows in Archery: Quivers, Arrow Rests and Holders Explained. If you want a broader view of rest options before you buy, Top 7 Archery Bow Arrow Rest Options Compared for Recurve and Compound Bows covers the main categories. Archers setting up a Hamskea model specifically may also find Hamskea Epsilon Arrow Rest: Setup, Tuning and Buying Guide useful.

FAQ

How often should I check my new rest’s tuning?

Check the tune after the first few shooting sessions, then every few weeks or after any change to your arrows or string. Mounting screws can loosen over time, so a quick alignment check is worth doing regularly.

Can I install a Hamskea arrow rest without a bow square?

You can, but a bow square makes alignment far more accurate. Without one, use a straightedge across the riser and check the rest against your arrow path with a measured reference.

What if my paper tear looks fine but my arrows still group poorly?

Paper tuning checks only one part of the system. Look at nock height, string wear, point weight and release consistency. Shoot a bare-shaft test and a group of several arrows before making more rest changes.

Conclusion

A new Hamskea arrow rest performs best when it is mounted square, set at the correct height and tuned with paper and bare-shaft tests. Make small adjustments, recheck after each change, and judge your tune from groups of arrows rather than single shots. Take your time with the setup, and your arrows will fly cleanly.

Ethan Brooks

About Ethan Brooks

Ethan Brooks is part of our editorial team and reviews and edits our target archery guides, checking product details against manufacturer specifications and owner feedback.

About the author

Ethan Brooks
Ethan Brooks

Ethan Brooks writes reviews and buying guides for Archery Society.