Hamskea Epsilon Arrow Rest: Setup, Tuning and Buying Guide
Learn how the hamskea epsilon arrow rest works, how to install and tune it, and what to check before you buy. A practical guide for new target archers.
Updated November 2026
The hamskea epsilon arrow rest is a drop-away style rest designed to hold your arrow securely at full draw and then get out of the way as the arrow leaves the bow. This guide explains what the rest does, how to install it on a riser, how to set it up for clean arrow flight, and what to look for when you are deciding whether it suits your setup. By the end, you should know how to mount it, set its position and timing, and spot the common problems before they cost you accuracy.
What the Hamskea Epsilon Arrow Rest Does
An arrow rest supports the arrow between the bow’s cutout and the riser, keeping the shaft from sagging or touching the riser during the shot. The hamskea epsilon arrow rest is a drop-away design, meaning a cable or drive mechanism lowers the rest arm away from the arrow at the moment of release. Drop-away rests are popular on compound bows because they reduce contact between the arrow and the rest, which tends to produce more consistent arrow flight when the rest is set correctly.
Shopping for one? See our guide: Arrow Rest for Compound Bow: 6 Best Picks Compared (2026).
Before you buy or mount one, confirm the rest fits your bow. Manufacturers typically specify compatibility by bow brand, riser type, and mounting hole pattern. Check the product documentation for mounting thread size, arrow diameter range, and whether the unit is intended for right-hand or left-hand shooters. If you are comparing options, the Drop Away Arrow Rest for Compound Bow: 7 Best Picks Compared (2026) roundup covers how drop-away designs differ in general.
Tools and Parts You Need Before Installation
Gather everything before you start so you are not improvising with the bow on the floor. A typical installation needs:
- Hex keys in the sizes listed in the rest’s instructions (commonly metric)
- A torque wrench or a fine-tip screwdriver for the mounting screws, so you avoid overtightening
- The rest’s mounting bracket or adapter, if your bow requires one
- Blue thread-locking compound for screws that can work loose under vibration
- A bow square and a tape measure for positioning checks
- A bow press, if your rest requires cable or cam tension adjustment
- Clean rags and a little isopropyl alcohol to remove grease from the riser
If you are new to working on bows, the Whisker Biscuit Arrow Rest Installation: A Step-by-Step Guide article walks through general rest mounting practices that apply to many designs.
How to Install the Hamskea Epsilon Arrow Rest Step by Step
Installation is mostly about getting the rest square to the bow and securing it so it does not shift. Work slowly and keep the bow unstrung unless the instructions say otherwise.
Step 1: Unstring the Bow and Mark Your Mounting Position
Unstring the bow and place it in a bow stand. Locate the rest mounting holes on the riser. Some shooters mark the expected centershot position with painter’s tape so they can compare their adjustments later.
Step 2: Attach the Mounting Bracket
Fit the bracket to the riser using the supplied screws. Hand-tighten first, then snug each screw in a crisscross pattern. Do not fully torque them yet. You need some room to move the rest during tuning.
Step 3: Attach the Rest Body and Drive Mechanism
Mount the rest body to the bracket and connect the drop-away drive component as the manual describes. Keep the cable or drive path free of kinks, since a bent cable can cause erratic drop timing.
Step 4: Set the Initial Centershot
Centershot is the horizontal alignment of the arrow with the bow’s center. A common starting point is to align the arrow tip with the string’s center when the bow is viewed from the back at full draw. Use a bow square to confirm the vertical plane, then adjust the rest horizontally until the arrow sits centered behind the arrow shelf. Many shooters aim for a starting centershot in the general range the bow manufacturer recommends, then refine it with paper tuning.
Step 5: Set the Rest Height and Arrow Contact Point
Set the rest height so the arrow sits level with the nock locator and the cable slide. A small height error can cause the arrow to ride slightly up or down, which shows up as a vertical tear in paper tests.
Step 6: Set the Drop-Away Timing
Timing determines when the rest drops away relative to the shot. Most drop-away designs use a cam or cable that triggers the drop as the string moves forward. Your goal is for the rest to clear the arrow before the fletching passes it. Check this by drawing the bow slowly with an arrow nocked and watching the rest through the release. Follow the manufacturer’s specified timing gap if one is provided.
Step 7: Tighten and Verify
Once your initial settings look right, tighten all screws to the torque specified in the manual, and apply thread-locking compound if the instructions recommend it. Recheck centershot and height after tightening, since mounting screws can shift slightly.
Tuning the Rest for Clean Arrow Flight
Mechanical setup gets you close, but tuning confirms the arrow actually flies straight. Paper tuning and bare-shaft tuning are the two methods most shooters use.
Paper Tuning Basics
Shoot an arrow through a sheet of paper stretched in a frame about three feet from the target. A correctly tuned arrow leaves a clean hole with the fletching centered on it. A tear pointing in a consistent direction tells you which adjustment to make. Small changes to rest position usually correct horizontal tears, and height or cable tension changes address vertical ones. Make one change at a time.
Bare-Shaft Tuning
Bare-shaft tuning compares arrows shot with and without fletching at the same distance. If the bare shaft and fletched arrow hit the same point, the setup is generally in good shape. If they diverge, adjust rest position and recheck. This method is useful when paper tuning gives mixed results.
Checklist for Setup Verification
- Confirm centershot with a bow square at full draw.
- Verify rest height against the nock locator.
- Check drop-away timing with a slow draw and release.
- Run a paper test at short range and read the tear.
- Repeat bare-shaft comparison at 20 yards.
- Recheck all screw torque after the first session.
Common Mistakes With the Hamskea Epsilon Arrow Rest
Most problems with drop-away rests trace back to a few predictable errors.
- Overtightening mounting screws. This can strip threads or warp the bracket. Use a torque wrench where the manual gives a value.
- Ignoring cable condition. A frayed or kinked cable changes timing unpredictably. Inspect it at every setup.
- Tuning too many variables at once. Change one setting, test, then decide on the next change.
- Skipping the recheck after shooting. Vibration from a full session can loosen settings slightly.
- Mismatched arrow spine. If your arrows are too stiff or too weak for your draw weight, no rest adjustment will fully correct the flight.
For broader setup issues and how rests interact with other components, the What Holds Arrows in Archery: Quivers, Arrow Rests and Holders Explained article explains how the rest fits into the overall arrow-holding system.
Buying Considerations for the Hamskea Epsilon Arrow Rest
If you are deciding whether this rest suits your bow and shooting style, compare it against other drop-away options on a few practical factors. The table below summarizes what to weigh.
| Factor | What to Check | Why It Matters |
|---|---|---|
| Bow compatibility | Mounting pattern and riser type in the spec sheet | A mismatch means improvised or unsafe mounting |
| Arrow diameter range | Manufacturer-stated limits | Oversized or undersized arrows can jam or fail to seat |
| Drive type | Cable, cam, or limb-driven mechanism | Affects drop timing and maintenance needs |
| Adjustment range | Centershot and height travel | Determines how much tuning you can do without remounting |
| Serviceability | Availability of replacement parts | Keeps the rest usable after normal wear |
Owners often report that drop-away rests with generous adjustment range make tuning easier, especially for shooters still learning their setup. If you are weighing drop-away against simpler whisker-style rests, the Drop Away Arrow Rest vs Whisker Biscuit: Which Should You Choose? comparison is a useful reference.
Recommended gear
A few supporting items make installation and tuning more reliable. The first is a stable bow stand, which keeps the riser at a consistent height while you adjust the rest. The second is a bow square, which confirms that your centershot measurements are taken on a true vertical plane. The third is a paper tuning frame, which gives you a consistent target for diagnosing arrow flight. The fourth is a torque-limiting hex driver set, which helps you tighten rest mounting screws to the values the manufacturer specifies without guessing.
- A sturdy bow stand that holds the riser steady during adjustments. View on Amazon
- A bow square for checking centershot and rest alignment. View on Amazon
- A paper tuning frame for diagnosing arrow flight at short range. View on Amazon
- A torque-limiting hex driver set for mounting screws. View on Amazon
Tips for Better Results
- Record your settings in a notebook, including centershot, height, and timing gap, so you can restore a known-good setup after a bow service.
- Recheck the rest after your first ten to twenty arrows, since early vibration often reveals loose hardware.
- Keep the drive cable clean and lightly lubricated only if the manual allows it.
- Store the bow in a case or on a rack that keeps the rest from being bumped, since a small knock can shift centershot.
FAQ
Is the hamskea epsilon arrow rest a drop-away rest?
Yes. It is designed to drop the arrow support away from the arrow at release, which reduces contact during the shot. Confirm the exact drive mechanism in the product documentation before mounting.
Do I need a bow press to install it?
Not always. A bow press is usually needed only if the installation requires cable or cam tension changes. If the manual calls for it, use a press rated for your bow.
How do I know if my centershot is correct?
Use a bow square at full draw and check that the arrow sits centered relative to the string. Then confirm with a paper test, since visual alignment alone does not guarantee clean flight.
What does a torn paper hole mean?
The direction of the tear indicates which adjustment may help. Horizontal tears often point to centershot, while vertical tears can relate to height or cable timing. Change one setting at a time.
How often should I check the rest?
Check it after mounting, after the first session, and periodically during regular shooting. Look for loose screws, cable wear, and any change in arrow flight.
Can I use this rest with any arrow?
Only within the arrow diameter range the manufacturer specifies. Arrow spine also matters for flight quality, so match your arrows to your draw weight and bow setup.
When should I have a professional service my bow?
If you are uncertain about cable routing, timing, or any step that involves tension, have a qualified archery technician or pro shop handle it. Improper bow adjustments can cause injury.
Conclusion
The hamskea epsilon arrow rest works best when it is mounted carefully, set to a known centershot and height, and tuned with paper or bare-shaft testing. Take your time with installation, change one variable at a time, and recheck your hardware after the first few sessions. With a methodical approach, you can achieve consistent arrow flight and spend more time focused on your shot.
Ready to choose one?
