We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

How to Tie Archery Arm Guard: A Step-by-Step Guide for Beginners

Learn how to tie an archery arm guard so it stays snug, protects your forearm and doesn't slip mid-shot. Clear steps, fit checks and common mistakes to avoid.

Updated November 2026

Learning how to tie archery arm guard straps correctly keeps the guard in place through every shot and protects your bow forearm from string slap. You will set the guard at the right height, fasten it snugly without cutting off circulation, and check that it stays put when you draw. The whole process takes under two minutes once you know the pattern.

Before You Start: Check the Fit

Most arm guards are designed to sit on the inside of your bow arm, running from just below the elbow toward the wrist. Before tying anything, slide the guard onto your forearm with the strap loose and confirm that it covers the area the string crosses during release. If you are not sure of the length, read the manufacturer’s sizing chart, since most guards list a forearm measurement in inches or centimeters.

Shopping for one? See our guide: 4 Best Archery Leather Arm Guard Options for Target Archers (2026).

Step-by-Step: Tying the Guard

  1. Hold the guard against the inside of your bow arm with the padded side facing the string.
  2. Wrap the strap once around your forearm, just above the wrist, and pull it firm but not tight.
  3. Thread the end through the buckle or tie point and fasten it. If your guard uses ties rather than buckles, make a single knot first, then a second overhand knot for security.
  4. Bring the upper strap around the forearm just below the elbow, keeping it parallel to the first strap.
  5. Fasten the second strap with the same method, adjusting so the guard sits flat with no wrinkles in the leather or fabric.
  6. Flex your bow hand and rotate your forearm. The guard should move with your arm without sliding toward your elbow or wrist.

Testing the Tension and Position

A correctly tied guard should be snug enough that you can slide a finger under the strap with a little resistance, but not so tight that your hand tingles or your fingers feel cold. Draw your bow to your anchor and release a few times at close range. If the guard shifts, retie it with slightly more tension on the upper strap, which is usually the one that controls movement.

Quick Fit Checklist

  • Guard covers the inside of the forearm from wrist to just below the elbow
  • Straps are snug, with one finger able to slide beneath
  • No wrinkles or folds under the padding
  • Guard stays in place during a full draw and release
  • Hand and fingers feel warm, not numb

Common Mistakes to Avoid

  • Tying too tight. Restricted blood flow causes numbness and can make your release less consistent.
  • Placing the guard too high. A guard that rides up toward the elbow leaves the wrist exposed to string slap.
  • Skipping the second knot. Single knots can loosen after several sessions of shooting.
  • Ignoring wear. Frayed straps or worn buckles should be replaced before they fail mid-shot.
  • Retying from scratch each time. Once you find the right tension, mark the strap position so future setup is faster.

If you have a numb hand, persistent pain or swelling after shooting, stop and consult a doctor or a qualified archery coach.

A sturdy, well-padded guard with adjustable straps makes tying and retying easier, especially for new archers still learning the right tension. View on Amazon Look for a model whose strap width matches your comfort preference.

A forearm sleeve can add protection on hot days or for shooters who prefer no strap pressure on bare skin. View on Amazon It works well as a base layer under a strap-on guard.

For more on sizing and materials, see Archery Arm Guard Use: How to Wear One Correctly and Protect Your Forearm and Archery Arm Guard Sleeve: How to Choose, Fit and Wear One (7 Steps). Archers with longer forearms may also find Long Archery Arm Guard: How to Choose, Fit and Use One Properly useful.

FAQ

How tight should an archery arm guard be?

It should be snug enough to stay in place during a full draw, with about one finger able to slide under the strap. If your hand feels numb or cold, loosen it.

Where should the arm guard sit on my arm?

It should cover the inside of the bow forearm from the wrist to just below the elbow, where the string is most likely to strike during release.

What if my arm guard keeps slipping?

Tighten the upper strap first, check that the guard is not too large for your forearm, and make sure the padding is not folded underneath.

Conclusion

Tying an arm guard correctly takes only a few minutes once you understand the fit points: wrist, mid-forearm and just below the elbow. Check the tension with a draw and release before shooting in earnest. Retie as needed, and replace worn straps before they fail.

Lauren Holland

About Lauren Holland

Lauren Holland is part of our editorial team and reviews and edits our target archery guides, checking product details against manufacturer specifications and owner feedback.

About the author

Lauren Holland
Lauren Holland

Lauren Holland writes reviews and buying guides for Archery Society.