How to Sight in a Single Pin Bow Sight: A Step-by-Step Guide
Learn how to sight in a single pin bow sight in clear steps: set your anchor, mark distances, adjust the pin and confirm groups at 20 yards.
Updated November 2026
Sighting in a single pin bow sight means adjusting one pin so it lines up with where your arrows actually land at a set distance. Once you finish, you will have a reliable starting point for a 20-yard pin and a repeatable process for setting the other distances you shoot. The whole job takes one range session if your bow is already tuned.
What You Need Before You Start
Gather the basics before you touch the sight. A sight that is loose, a bow that is out of tune or an inconsistent anchor will make every adjustment look wrong.
Shopping for one? See our guide: Bow Sights with Rangefinder: 5 Best Picks Compared (2026).
- A tuned compound or recurve bow with arrows cut to the correct length
- A target at a known distance, starting at 20 yards
- A hex or Allen key matching your sight’s adjustment screws
- Painter’s tape or a small aiming dot for the target face
- A stable shooting bench or a rested stance
Step-by-Step Sight-In Process
Step 1: Confirm the Sight Is Mounted Solidly
Check that the sight bracket is tight and the sight sits level with the arrow path. A sight that wobbles or rotates will shift your point of impact even when your form is perfect. Recheck the screws after your first few shots, because they can loosen under vibration.
Step 2: Set Your Anchor and Form
Use the same draw length, anchor point and release every time. Your sight can only tell you where the arrow goes if your shooting stays consistent. If your groups scatter widely, fix your form before you adjust the sight.
Step 3: Shoot Groups at 20 Yards
Place the target at exactly 20 yards and shoot three to five arrows, aiming at the same spot each time. Do not chase a single good arrow. Look at the group as a whole and note where most of the arrows land relative to your aiming point. For another angle, check out Running Belt Race Number: How to Attach, Position and Pin Your Bib.
Step 4: Adjust the Pin
Move the pin toward the group, not toward the bullseye of your last arrow. Vertical adjustment moves the group up or down, and horizontal adjustment moves it left or right. Make small changes, then shoot another group before adjusting again. Many sights also have a windage screw for side-to-side movement, so check the adjustment direction on your model before turning anything.
Step 5: Mark the Pin Position
When the group sits where you want it, mark the pin’s setting with a dab of paint or a small piece of tape on the sight housing. This gives you a quick reference if the sight gets bumped during transport.
Setting Additional Distances
Once your 20-yard pin is set, you can move the target to 30, 40 or 50 yards and repeat the same process for each distance. Some archers use a sight tape or a dial to track each setting, and the setup guides linked below explain those systems in more detail. Check your sight’s instructions for the correct adjustment rules for each distance.
| Distance | What to Check |
|---|---|
| 20 yards | Group is centered on aiming point |
| 30 yards | Pin adjustment matches the group, not the 20-yard setting |
| 40 yards | Arrow flight is consistent with your form |
Common Mistakes
- Adjusting after a single arrow instead of a full group
- Making large pin changes that overshoot the target
- Sighting in with an inconsistent anchor or release
- Forgetting to recheck the sight bracket after a few sessions
- Shooting at an unmarked distance, which makes the adjustment hard to repeat
Recommended Gear
- Hex key set for bow sights: A small set with the correct sizes makes adjustments quicker and avoids stripping screws. View on Amazon
- Bow sight level: A level helps you confirm the sight is mounted upright before you start shooting. View on Amazon
- Archery target with a clear aiming face: A large target with a visible center lets you read your groups easily at each distance. View on Amazon
FAQ
How many arrows should I shoot before adjusting the pin?
Shoot three to five arrows at each distance and look at the group as a whole. A single arrow can mislead you because of small form errors.
Why does my pin keep moving after I set it?
Loose sight screws or a bumped bracket are the most common causes. Recheck the mounting hardware and mark the pin position so you can spot changes quickly.
Do I need to sight in again after changing arrows?
Yes, a new arrow weight, length or point can change where the arrow lands. Recheck your 20-yard setting first, then confirm the other distances. For guidance on related setup, see Single Pin Dial Bow Sight: How to Set Up and Sight In for Beginners.
Conclusion
Sighting in a single pin bow sight comes down to solid mounting, consistent form and small, deliberate adjustments at a fixed distance. Shoot groups, not single arrows, and mark your settings as you go. For more help with setup, read Single Pin Bow Sight Tape: How to Set Up and Use One Correctly and How to Sight in Compound Bow: A Step-by-Step Guide for Beginners.
Related reading
- Triple Stack Bow Sight: How to Set Up and Sight In a Three-Pin Sight
- Iq Single Pin Bow Sight: Setup and Aiming Guide for Beginners
- Hha Picatinny Bow Sight: How to Mount and Set Up Your Pin Sight
Ready to choose one?
