We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

How to Sight in Compound Bow: A Step-by-Step Guide for Beginners

Learn how to sight in a compound bow at 20 yards with a clear step-by-step process, from setup checks to fine-tuning your pins for accurate shots.

Updated November 2026

Sighting in a compound bow means adjusting your sight pins so that an arrow lands where your pin points at a known distance. Done properly, this takes about an hour and gives you a repeatable aim point you can trust. The process below covers how to sight a compound bow from start to finish, using a 20-yard starting distance that works for most backyard and club setups.

What You Need Before You Start

Gather everything before you shoot so you are not walking back and forth between the line and the target. Work from a stable shooting position, and confirm your bow is tuned before you touch the sight.

Shopping for one? See our guide: Bow Sights with Rangefinder: 5 Best Picks Compared (2026). We also found Bow Mounted Fish Finder: How to Choose and Install One (2026) useful on this point.

  • A bow that is already tuned, with arrows that are correctly spined for your draw weight and length
  • A target at 20 yards, a measured tape or range markers to confirm distance
  • A bow sight with pins and an adjustment wrench or screwdriver for the sight housing
  • A bag of arrows, ideally a dozen or more, and a stable bench or shooting stand
  • A way to record each group, such as a notepad or a target face with a grid

Step-by-Step: Setting the First Pin

Start with the bow level and your anchor point consistent on every shot. Inconsistent anchor or grip is the most common reason sight settings never seem to settle. Once you have a repeatable form, you can begin adjusting the sight.

  1. Set the sight housing so the top pin is roughly aligned with the center of the target at 20 yards. Use the windage adjustment to center the sight left to right first.
  2. Shoot three to four arrows from a rested position, focusing on the same anchor point and release each time.
  3. Find the group center. If arrows land high, lower the pin by adjusting the sight’s vertical screw. If they land low, raise it.
  4. Make small changes, about a quarter to a half turn at a time, then shoot another group before adjusting again.
  5. Once the first pin hits center at 20 yards, lock the adjustment and confirm the group is tight.

Adding Your Remaining Pins

Once your 20-yard pin is set, you can establish the other distances. Most compound sights have multiple pins, and each one should be set at a specific yardage. Moving back in increments makes the process more manageable.

  • Move to 30 yards and shoot a group with the second pin. Adjust only that pin until the group center is on the target.
  • Repeat at 40, 50 or 60 yards, depending on how far you plan to shoot in the field.
  • Mark each pin’s distance on the sight or in a notebook so you remember which pin belongs to which yardage.

Checking Your Work

After all pins are set, shoot a fresh group at each distance without changing anything. Tight groups at each yardage mean your sight is ready. If groups drift, check your anchor point and release before making further adjustments to the sight.

Common Mistakes to Avoid

  • Adjusting the sight before the bow is tuned, which makes accurate setup impossible
  • Changing your anchor point, grip or release between groups
  • Making large sight adjustments instead of small, incremental turns
  • Shooting while tired, since fatigue changes your form and throws off results
  • Skipping the distance check, so pins end up set for guessed yardages instead of measured ones

A stable bow stand keeps your bow level across shots, which helps you read each group accurately. Check the lock nuts on your sight after every session, since vibration can shift settings. A quality bow sight with clear pin markings and fine-adjustment screws makes small corrections much easier.

  • A bow stand or shooting bench for consistent, level shooting. View on Amazon
  • A bow sight with fine vertical and windage adjustment for precise pin setting. View on Amazon
  • A target stand or foam block for safe, repeatable 20-yard practice. View on Amazon

FAQ

How far should I start when sighting in a compound bow?

Most people start at 20 yards because it is close enough to build a tight group and far enough to show small errors. Once the first pin is centered, you can move back to longer distances.

How often should I re-sight my compound bow?

Check your sight whenever you change arrows, string, cams, or your draw length, and periodically during the season. Small shifts can happen over time, so a quick check at 20 yards is a good habit.

Can I sight in a compound bow without a rangefinder?

Yes. Measure your distances with a tape or marked range, then set each pin at a known yardage. A rangefinder helps in the field, but it is not required for setting pins on a measured range.

Conclusion

Sighting in a compound bow comes down to a tuned bow, consistent form and small, methodical adjustments. Set your 20-yard pin first, then build outward one distance at a time. Once your groups stay tight at every yardage, your sight is ready for practice and the field.

Ethan Brooks

About Ethan Brooks

Ethan Brooks is part of our editorial team and reviews and edits our target archery guides, checking product details against manufacturer specifications and owner feedback.

About the author

Ethan Brooks
Ethan Brooks

Ethan Brooks writes reviews and buying guides for Archery Society.