We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

How to Mount a Bow Sight: A Step-by-Step Guide for Beginners

Learn how to mount a bow sight step by step, from choosing the right bracket height to squaring the sight and tightening mounts without damaging your bow.

Updated November 2026

Learning how to mount a bow sight comes down to four things: attaching the sight bracket to your bow, squaring it to the riser, setting the correct height, and tightening everything to spec. Done in order, the job takes under an hour and gives you a sight that holds its position between sessions. This guide walks through each step for compound and recurve setups using a standard bracket-style sight.

Before You Start: Check Your Bracket and Bow

Confirm that your sight bracket matches your bow’s mounting pattern. Most sights use a standard threaded bracket, but some bows use a Picatinny rail or a dovetail. Check the owner’s manual or your bow’s specification sheet for the correct bolt size and torque range before you pick up a wrench. Keep the bow on a padded surface or bow stand so the limbs and cams are not stressed during the work.

Shopping for one? See our guide: Bow Sights with Rangefinder: 5 Best Picks Compared (2026).

Step-by-Step: Mounting the Sight

  1. Thread the sight onto the bracket, leaving the mounting screws slightly loose so you can adjust the sight later.
  2. Attach the bracket to the riser using the supplied bolts. Start each bolt by hand to avoid cross-threading.
  3. Set the sight’s vertical position so the pin guard sits roughly parallel to the riser, leaving room for the arrow to clear.
  4. Square the sight to the bow. Hold the bow at full draw, or use a bow square, and check that the pin housing is aligned with the arrow’s flight path.
  5. Tighten the bracket bolts evenly, alternating between them, to the torque value in your manual. If no value is listed, snug them firmly without forcing the threads.
  6. Check that the sight moves freely on its adjustment slots and that no part contacts the string, cams or cables at full draw.

Setting the Sight Height and Alignment

Once the sight is mounted, set the height so the pin housing lines up with your aiming eye at full draw. Draw the bow, close one eye, and check that the sight’s pins sit in your natural line of sight without you tilting your head. Adjust the vertical slot in small increments and recheck at full draw each time. A sight that is too low or too far forward will force an awkward anchor and inconsistent aim. If you want more background, see Bike Helmet Rear View Mirror: How to Choose and Mount One Safely.

Alignment matters as much as height. A sight that leans even slightly to one side will shift your point of impact at distance. Use a bow square or a plumb line against a known vertical surface to confirm the pins are centered over the arrow path, then lock the sight in place.

Common Mistakes

  • Overtightening bracket bolts, which can strip threads in the riser.
  • Mounting the sight before the bow is set up at your draw length, then having to remount it.
  • Skipping the full-draw check, which hides clearance problems until you shoot.
  • Tightening one bolt fully before the others, which pulls the bracket out of square.
  • Assuming a new sight is aligned straight out of the box. Always verify before sighting in.
  • Bow square: Helps you confirm the sight is square to the arrow path before you tighten anything. View on Amazon
  • Hex key set and torque driver: Lets you tighten bracket bolts to a controlled value instead of guessing. View on Amazon

FAQ

Do I need a bow press to mount a bow sight?

No. A bow press is only needed if you are removing or installing cams or limbs. Mounting a sight to a riser can be done with the bow on a stand or padded surface.

How tight should the sight bolts be?

Tighten them to the torque value in your bow or sight manual. If no value is given, snug them firmly and evenly without forcing them, since overtightening can strip threads.

Should I re-square the sight after a few weeks of shooting?

Yes, it is a good habit. Vibration can loosen brackets slightly, so check alignment and bolt tightness every few weeks. If you are unsure about a repair, consult a qualified archery pro shop.

Conclusion

Mounting a bow sight is a methodical job: fit the bracket, square the sight, set the height, and tighten to spec. Verify clearance at full draw before you start sighting in. For more detail on the next step, see How to Sight in Compound Bow: A Step-by-Step Guide for Beginners.

Ethan Brooks

About Ethan Brooks

Ethan Brooks is part of our editorial team and reviews and edits our target archery guides, checking product details against manufacturer specifications and owner feedback.

About the author

Ethan Brooks
Ethan Brooks

Ethan Brooks writes reviews and buying guides for Archery Society.