How to Install Bow Sight: A Step-by-Step Guide for Beginners
Learn how to install bow sight on your compound or recurve bow with this step-by-step guide covering tools, mounting, tightening and a final check.
Updated November 2026
Learning how to install bow sight correctly takes about 20 to 30 minutes with basic hand tools. By the end of this guide, you will have a sight that is mounted square to the riser, tightened to the manufacturer’s torque range, and ready for sighting in. Most problems archers have later trace back to a sloppy mount, so the steps below focus on alignment before tightening.
What You Need Before You Start
Gather everything first so you are not hunting for tools with the bow half-assembled. Check your sight’s instruction sheet for the exact screw size and any torque figures.
Shopping for one? See our guide: Bow Sights with Rangefinder: 5 Best Picks Compared (2026).
- The bow sight, with its mounting bracket and screws
- Hex keys (Allen wrenches) in the sizes listed in the sight’s manual
- A torque-limiting screwdriver or hex driver, if the manufacturer specifies a torque value
- Thread-locking compound, only if the manufacturer recommends it
- A clean cloth and a bow stand or padded surface
Step-by-Step: Mounting the Sight Bracket
Place the bow on a stand with the riser secured. Locate the sight mounting holes on the riser, usually a pattern of threaded holes on the sight window side. Wipe away any grit from the holes, since debris can cause the bracket to sit crooked.
- Slide the sight bracket onto the riser and start the mounting screws by hand. Do not fully tighten yet.
- Set the sight so the pin guard or sight window clears the arrow shelf and the string path with room to spare.
- Adjust the bracket up or down, and left or right, until the sight housing is level and centered over the arrow when you look down the shaft.
- Confirm the bracket is square to the riser. A small level or a straightedge held against the sight body helps here.
- Tighten the screws evenly, alternating between them in small increments so the bracket does not tilt.
Setting Torque Correctly
Many sight manuals give a torque range in inch-pounds. Overtightening can strip threads in aluminum risers, while undertightening lets the sight drift during shooting. If your sight lists a torque value, use a torque-limiting driver and stop at that number. If it does not, snug each screw firmly and then give it a slight additional turn.
Checking Clearance and Alignment
Before you call the installation finished, draw the string back to full draw without an arrow. Watch the string and cams for contact with the sight pins or bracket. Check that the sight moves freely up and down along its slide and that the pins do not bind. Make any alignment changes now, then retighten and recheck.
If you are also adding a peep or other accessories, leave final adjustments for later. Once the sight is solidly mounted, you can move on to the setup steps in How to Sight in Compound Bow: A Step-by-Step Guide for Beginners.
Common Mistakes to Avoid
- Tightening one screw fully before starting the others, which pulls the bracket out of square.
- Skipping the clearance check at full draw, which can cause string contact and poor arrow flight.
- Using thread-locker where the manufacturer does not recommend it, making later removal difficult.
- Mounting the sight with grit in the threaded holes.
- Forgetting to recheck screw tightness after the first few shooting sessions.
Recommended Gear
A torque-limiting hex driver set helps you hit the manufacturer’s specified range without guesswork. View on Amazon
A small bubble level or magnetic level makes it easier to confirm the bracket sits square to the riser. View on Amazon
A bow stand with padded cradles keeps the riser steady and protects the finish while you work. View on Amazon
FAQ
Do I need a bow press to install a bow sight?
No. Bow sights mount to the riser without bow compression on most compound and recurve designs. Use a bow stand to keep the riser steady.
What if my sight does not line up with the arrow?
Loosen the bracket slightly and adjust the sight left, right, up or down until it is centered over the arrow path. Retighten evenly and recheck clearance.
Should I check the sight again after shooting?
Yes. Vibration can loosen screws over time, so recheck tightness after your first several sessions and periodically after that. For bow-specific safety questions, consult a qualified archery pro shop.
Conclusion
A properly installed bow sight starts with a square, level mount and screws tightened in even steps to the manufacturer’s range. Take time to check clearance at full draw before you call the job done. Once the sight is secure, you are ready to set your pins and begin sighting in.
Related reading
- Bow Sight Mounting Screws: How to Install and Tighten Them Correctly
- Bow Peep Sight Tube: How to Install and Align One (Step by Step)
- Battery for Bow Sight Light: How to Choose, Install and Replace It
Ready to choose one?
