How to Fix a Peep Sight on a Bow: Step-by-Step Repair Guide
Learn how to fix a peep sight on a bow in a few steps. Fix a twisted, loose or misaligned peep so your sight picture stays consistent and your groups tighten.
Updated November 2026
To fix a peep sight on a bow, you need to straighten the peep so its aperture sits level and centered in your string, then tighten it so it stops rotating under string tension. Most peep problems come from a worn or stretched serving, a loose or cut peep tying, or a peep that was tied at the wrong height. The steps below cover how to diagnose the problem and correct it without replacing the string.
If your peep keeps twisting after a fix, the cause is usually the serving or the tie, not the peep itself. For a fuller walkthrough of that specific issue, see Peep Sight on Bow Keeps Twisting? How to Fix It Step by Step.
Shopping for one? See our guide: Bow Sights with Rangefinder: 5 Best Picks Compared (2026).
Before You Start: Diagnose the Problem
Draw the bow slowly to full draw and look through the peep. Note which way the aperture is off. A peep that tilts to one side is rotated. A peep that sits too high or too low is mis-tied. A peep that wobbles when you draw is loose.
- Rotated: the aperture leans left or right relative to the string.
- Height off: the peep sits above or below your intended anchor.
- Loose: the peep slides or spins when you release tension.
Check that your bow is unstrung or at reduced tension before you touch the peep. Strings under full load can snap or cause injury if a serving is cut.
How to Fix a Peep Sight That Is Rotated or Loose
- Unstring the bow or let the string rest at low tension, then inspect the serving where the peep is tied.
- Loosen the peep tie with a bow-square or a small pick. Do not cut the string unless you plan to re-serve it.
- Rotate the peep so its aperture sits square to the string. Hold it with your fingers while you check alignment against the string’s center.
- Re-tie the peep with two or three tight half hitches on each side, pulling each one down against the peep before tightening the next.
- Brace the bow and draw to anchor. Check the aperture again. Make small adjustments by backing off one tie and re-tying.
Checking the Serving
If the serving is frayed, stretched or flattened, the peep will slip no matter how well you tie it. Remove the damaged section and re-serve, or have a qualified bowstring technician do it. Re-serving changes string length slightly, so recheck your braced height afterward.
How to Fix a Peep Sight at the Wrong Height
A peep tied too high or low changes your anchor point and your sight picture. Adjust height by sliding the peep up or down the string before you tighten the final tie. Work in small steps, usually a quarter inch at a time, and re-check at full draw after each change.
| Symptom | Likely cause | Fix |
|---|---|---|
| Aperture leans one way | Peep rotated in tie | Re-tie with peep square to string |
| Peep sits too high or low | Tie placed at wrong height | Slide peep to correct height, then re-tie |
| Peep spins under draw | Tie too loose or serving worn | Tighten tie or re-serve the section |
Common Mistakes to Avoid
- Tightening one side of the tie completely before the other, which locks the peep at an angle.
- Skipping a brace-height check after re-tying, which can change draw length or cam timing on compound bows.
- Cutting the string to remove the peep when a simple re-tie would have worked.
- Ignoring a worn serving and re-tying over it, which only delays the next failure.
- Making large height changes in one step instead of small adjustments you can check at full draw.
Recommended Gear
- Bow square: helps you check that the peep and nock point sit square to the string. View on Amazon
- Bowstring serving thread: used to re-serve a damaged section so the peep has a firm base. View on Amazon
FAQ
Can I fix a peep sight without unstringing the bow?
Sometimes you can make small height or rotation adjustments with the string still on, but you will need to brace the bow to check alignment. Unstringing gives you better access to the tie and is safer for a serving repair.
How often should I check my peep sight?
Check it before each shooting session, especially if you notice the sight picture changing. Peeps can settle or loosen after many shots, particularly on new strings.
When should I take the bow to a shop?
If the serving is badly worn, the string shows fraying, or you are unsure about brace height or string tension after a repair, have a qualified bow technician inspect it. Working with string tension carries real risk, so a professional check is worth the time.
Conclusion
A peep sight that is rotated, loose or set at the wrong height can be corrected with careful re-tying and a brace-height check. Diagnose the problem first, adjust in small steps and check at full draw. If the serving is damaged, re-serve it rather than re-tying over the wear.
Related reading
- Bow Peep Sight Tube: How to Install and Align One (Step by Step)
- What Is a Sight Master Bow Sight and How Do You Set One Up?
- What Is a Dead Ringer Bow Sight and How Do You Use One?
Ready to choose one?
